Használati útmutató Manhattan 180535
Manhattan
nincs kategorizálva
180535
Olvassa el alább 📖 a magyar nyelvű használati útmutatót Manhattan 180535 (16 oldal) a nincs kategorizálva kategóriában. Ezt az útmutatót 4 ember találta hasznosnak és 2.5 felhasználó értékelte átlagosan 4.7 csillagra
Oldal 1/16

For additional benefits
10-Port AC
Charging Cabinet
Instructions
Model 180535
or visit: register.manhattanproducts.com/r/180535
Scan to
register your
product warranty

For specifications, please visit manhattanproducts.com register.. Register your product at
manhattanproducts.com/r/180535 or scan the QR code on the cover.
Setup
1 Unlock unit door and open it.
2 To fit larger devices, remove bay divider(s).
• Unscrew bar and set it aside.
• To remove divider, pull up on the clip to release it from the bar it’s attached to.
• When enough dividers are removed, replace numbered bar and screws.
3 Connect devices to power outlets with appropriate cables. Secure cables with wire clips on dividers.
• Remove screws that hold the power box in place; slide the power box out.
• Connect power cables to power outlets, feeding cables through holes on power panel.
• Push the power box back in and replace the screws that hold it in place.
• Load devices in bays.
• Connect cables to devices.
Charging
4 Connect unit power cable to power outlet. Unit automatically begins to charge devices.
Installation Options
The following sections offer optional steps to complete installation.
To Reverse the Door — NOTE: Make sure all power is cut off from unit!
1 Unscrew grounding cable from door and cabinet. Remove door from cabinet by pulling L-shaped pins.2
1
3
2
Instructions
English

3 Flip door and guide pins into holes on other side of
cabinet frame. Release pins and ensure door is
secure.
4 Reattach grounding cable to door and cabinet.
Mounting to the Wall
1 At desired location on wall, use the spacing
shown in the graphic below to mark four level
drill positions for the cabinet holes.
Concrete wall: use a 15/64” (6 mm) bit to drill
holes 2.4 in. (60 mm) deep at marks.
Wood-stud walls: use a 15/64” (6 mm) bit to
make pilot holes 2.4 in. (60 mm) deep at marks.
2 Install included screws into holes so they
protrude 0.4 in. (10 mm) from the wall.
3 Position cabinet holes over wall screws and
hang cabinet on them. Installation is complete.
Stacking the Units — NOTE: Make sure all power is cut off from unit!
Stacking material not included; refer to website.
1 Unscrew the screws on the power box.
2 Slide the power box out.
3 Align the stacking holes on the top and bottom of
the cabinets.
4 Tighten screws (not included) into both cabinets
from the ceiling of the bottom cabinet.
5 Reinstall the power box with its screws.
16in. (406.4 mm)
16.57in. (420.86mm)
2 in.
(50mm)
NOTE: a 13 mm
(0.51 in.) gap exists.
3
Instructions
English
Termékspecifikációk
Márka: | Manhattan |
Kategória: | nincs kategorizálva |
Modell: | 180535 |
Szüksége van segítségre?
Ha segítségre van szüksége Manhattan 180535, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek
Útmutatók nincs kategorizálva Manhattan
3 Április 2025
3 Április 2025
12 Január 2025
3 Szeptember 2024
2 Szeptember 2024
2 Szeptember 2024
2 Szeptember 2024
2 Szeptember 2024
1 Szeptember 2024
1 Szeptember 2024
Útmutatók nincs kategorizálva
- nincs kategorizálva TRENDnet
- nincs kategorizálva Buzz Rack
- nincs kategorizálva DPA
- nincs kategorizálva KEF
- nincs kategorizálva Perlick
- nincs kategorizálva Toshiba
- nincs kategorizálva Spring
- nincs kategorizálva ZLine
- nincs kategorizálva Asus
- nincs kategorizálva Excalibur
- nincs kategorizálva SoundTube
- nincs kategorizálva Tower
- nincs kategorizálva Raidsonic
- nincs kategorizálva XTRARM
- nincs kategorizálva Globo
Legújabb útmutatók nincs kategorizálva
10 Április 2025
10 Április 2025
10 Április 2025
9 Április 2025
9 Április 2025
9 Április 2025
9 Április 2025
9 Április 2025
9 Április 2025
9 Április 2025