Használati útmutató Martin THRILL Multi-FX LED
Martin
Megkönnyebbülés
THRILL Multi-FX LED
Olvassa el alább 📖 a magyar nyelvű használati útmutatót Martin THRILL Multi-FX LED (3 oldal) a Megkönnyebbülés kategóriában. Ezt az útmutatót 17 ember találta hasznosnak és 9 felhasználó értékelte átlagosan 4.5 csillagra
Oldal 1/3
THRILL Multi-FX LED
User Guide
WARNING!
Read the Safety and Installation Guide supplied
with this product before installing or using this
product.
Fixture overview
1
White strobe LEDs
8
DMX in
2
Multibeam lens es
9
Hand wheel
3
Laser aperture
10
User Interface
4
Mounting bracket
11
Secondary attachment point
5
Clamp attachment point
12
Laser lockout switch
6
Microphone
13
AC mains out
7
DMX out
14
AC mains in & fuse
Using the control menu
The control menu is shown below. To
access the menu, press the MENU button.
Scroll through options with the (down) ▼
and ▲ (up) buttons. Press ENTER to select
an option. To return to a higher level in the menu, press MENU.
To exit the menu, press and hold MENU or wait a few seconds.
The default menu settings are shown in . bold
Menu
Sub-menu
Explanation
Set DMX address
Select 2-channel DMX personality
Select 16-channel DMX personality
Set xture mode to client 1
Set xture mode 2 to client
Set Master xture
-
Show selection o
Set Automatic trigger
Select preprogrammed show.
Select auto-trigger speed from 1-8
Toggle sound activation on/o
Set microphone sensitivity
Black out if no DMX
Run stand-alone show if no DMX
Hold last values if no DMX
/
Toggle display on/o
Inverted/normal display
Set multibeam eects (DMX ch 1)
Set multibeam intensity (ch 2)
Set red intensity (ch 3)
Set green intensity (ch 4)
Set blue intensity (ch 5)
Set amber intensity (ch 6)
Set white intensity (ch 7)
Set preset color value/eect (ch 8)
Set multibeam eect rotation (ch 9)
Set strobe intensity (ch 10)
Set strobe eect (ch 11)
Set strobe eect speed (ch 12)
Set laser eect (ch 13)
Set laser eect rotation (ch 14)
Run test of all eects
Readout xture hours
Readout rmware version
/
Reset to default values
Show Mode operation
The Multi-FX LED provides 8 pre-programmed shows that can be
selected from a DMX controller or from the control panel in Show
Mode. The shows use dierent variations of strobe, multibeam,
and laser eects, that can be triggered automatically or by sound.
Enable Show Mode
For Show Mode operation, the xture must not be receiving
commands from a DMX controller. It must be set to run in Show
Mode when there is no DMX signal. Show mode settings are
stored to an EPROM chip, and can be recalled even after
powered o. Enable Show Mode as follows :
1. Press MENU to enter the control menu.
2. Scroll to . Press ENTER.
3. Scroll to . Press ENTER.
Show selection
To select programmed show: a
1. Scroll to . Press ENTER.
2. Scroll to Press ENTER-.
3. Scroll to a show from 1 - 8, or select to run all shows.
4. Press ENTER.
Sound/Auto trigger selection
Shows can be automatically triggered or sound triggered. To
select the trigger type:
1. Scroll to . Press ENTER.
2. Select to enable sound trigger, or to enable auto-
trigger.
3. Press ENTER.
Auto trigger speed
If using auto trigger, set the speed as follows:
1. Scroll to Press ENTER..
2. Scroll to Press ENTER..
3. Select a trigger speed from (slow) to (fast). Press
ENTER.
4. Press and hold MENU to start show mode operation.
Microphone sensitivity ( )
If using sound trigger, adjust microphone sensitivity as follows:
1. Scroll to . Press ENTER.
2. Press to make the xture more responsive, up to 100.▲
Press to make the xture less responsive, down to 0.▼
3. Press ENTER.
4. Press and hold start show MENU to mode operation.
Master/client operation
Up to 32 Multi-FX LED xtures can be linked in a chain for
synchronized operation where the rst xture controls the others
using the rst fixture’s Show Mode settings.
Two modes are available. When set to Mode 1, client Client
xtures behave exactly like the master. In Mode 2, xtures Client
synchronize with the master xture with slightly dierent routines.
Note: Having more than one master xture may cause
damage. Set xtures before connecting them to the rst client
xture.
To the xture be set rst to the master:
1. Press MENU to enter the control menu.
2. Scroll to . Press ENTER.
3. Scroll to Press ENTER to set as master..
Set the master fixture’s show mode options as described above.
To the be set other xtures to clients:
1. Press MENU to enter the control menu.
2. Scroll to . Press ENTER.
3. Select or Press ENTER. .
4. Press and hold MENU to exit the menu.
Connect xtures to the master xture using DMX cable. client
Connect the master fixture’s DMX OUT socket to the DMX IN
socket of the rst xture. Continue connecting DMX OUT to client
DMX IN as described in the Safety and Installation Guide.
DMX operation
T Multi-FX LED may be linked to a DMX controller and he
operated DMX mode The xture has two DMX personality in .
modes: a 2-channel mode that provides remote control of show
mode options, and a 16-channel mode that provides full control
of each eect including Show Mode options. The xture
automatically runs in the selected DMX personality mode when
connected to an operating controller .
The fixture’s DMX start address must be set to match the address
assigned to it on the DMX controller .
The control panel indicates DMX mode operation by displaying
the fixture’s DMX start address.
To select the DMX personality de: mo
1. Press MENU to enter the control menu.
2. Scroll to . Press ENTER.
3. orScroll to the desired mode: . Press ENTER.
4. Press and hold MENU to exit the menu.
Assign an address for the xture on the DMX controller. Then set
the address on the Multi-FX LED as follows:
1. Press MENU to enter the control menu.
2. Scroll to . Press ENTER.
3. Scroll to the address assigned to the xture. Press ENTER.
4. Press and hold MENU to exit the menu.
For independent control, each xture must have its own unique
address and control channels. Two or more Multi-FX LED xtures
may have the same address if symmetric control is desired.
DMX commands 2 Channel Mode ,
Ch.
Value
Function
1
0-7
8- 37
38 67-
68 97-
98-127
128-157
158-187
188-217
218-247
248-255
Show Selection
O (no show)
Show 1
Show 2
Show 3
Show 4
Show 5
Show 6
Show 7
Show 8
Random Show
2
0- 10
11-255
Trigger Selection and Speed
Sound activation
Auto trigger, slow to fast
DMX Commands, 16 Channel Mode
Ch.
Value
Function
1
0-7
Multibeam Eects Selection
Multi eect o beam
1
2
4
9
3
5
6
7
8
10
11
12
13
14
Lasers can cause serious injury. Read the
Safety and Installation Guide before use.
IN INOUT OUT IN OUT IN OUT
Termékspecifikációk
| Márka: | Martin |
| Kategória: | Megkönnyebbülés |
| Modell: | THRILL Multi-FX LED |
Szüksége van segítségre?
Ha segítségre van szüksége Martin THRILL Multi-FX LED, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek
Útmutatók Megkönnyebbülés Martin
29 December 2024
27 Augusztus 2024
21 Augusztus 2024
20 Augusztus 2024
20 Augusztus 2024
20 Augusztus 2024
19 Augusztus 2024
19 Augusztus 2024
19 Augusztus 2024
19 Augusztus 2024
Útmutatók Megkönnyebbülés
- Megkönnyebbülés Nitecore
- Megkönnyebbülés Meipos
- Megkönnyebbülés Canarm
- Megkönnyebbülés Razer
- Megkönnyebbülés Sonneman
- Megkönnyebbülés WAC Lighting
- Megkönnyebbülés Theben
- Megkönnyebbülés Mtx Audio
- Megkönnyebbülés Auriol
- Megkönnyebbülés Litegear
- Megkönnyebbülés GoGen
- Megkönnyebbülés Mellert SLT
- Megkönnyebbülés Claypaky
- Megkönnyebbülés Dainolite
- Megkönnyebbülés Ecomed
Legújabb útmutatók Megkönnyebbülés
9 Április 2025
9 Április 2025
9 Április 2025
8 Április 2025
8 Április 2025
8 Április 2025
7 Április 2025
5 Április 2025
5 Április 2025
5 Április 2025