Használati útmutató Nectre MK1 LE
Olvassa el alább 📖 a magyar nyelvű használati útmutatót Nectre MK1 LE (8 oldal) a Fűtő kategóriában. Ezt az útmutatót 11 ember találta hasznosnak és 6 felhasználó értékelte átlagosan 4.3 csillagra
Oldal 1/8
Revision B
Nectre 1 MK LE
Installaon Instrucons
Keep these instrucons for future reference
Glen Dimplex Australia proudly supports the acvies of Landcare Australia through its membership of the AHHA
1
CONTENTS
1. INSTALLATION ................................................................... 1
1.1. IMPORTANT INFORMATION .................................... 1
1.2. FITTING REAR HEAT SHIELD ..................................... 2
1.3. INSTALLING THE HEATER ......................................... 2
1.3.1. Posioning the Heater 2 ........................................
1.3.2. Standard Installaon ........................................... 2
1.3.3. Corner Installaon 3 ..............................................
1.3.4. Clearance Dimensions ......................................... 3
1.3.5. Floor Protector .................................................... 3
1.4. REDUCING CLEARANCES TO COMBUSTIBLES .......... 3
1.5. INSTALLING THE FLUE .............................................. 4
1.6. INSTALLING FIRE BRICKS .......................................... 5
1.7. INSTALLING BAFFLE PLATES 5 .....................................
1.8. INSTALLING ASH PLATE 5 ...........................................
1.9. TECHNICAL DRAWINGS 6 ...........................................
1.9.1. MK1 Legs ............................................................. 6
1.9.2. MK1 Ped .............................................................. 6
1. INSTALLATION
1.1. IMPORTANT INFORMATION
The unit must be installed according to all manufacturers’
instrucons included in manual. The manufacturer is not this
liable for installaons that do not meet the requirements
outlined in this manual.
Most building regulatory authories in Australia require any
wood heater installaon to comply with Installaon Standard
AS/NZS 2918. Dierent states and councils may have varying
regulaons. Check local building regulaons before installing
the appliance.
All Nectre wood heaters have been tested to ensure they will
meet the appropriate safety standard requirements if the
instrucons in this manual are followed. As the safety and
emissions performance can be aected by altering the
appliance, no modicaons are allowed without wrien
permission from the manufacturer.
WE RECOMMEND THAT THE INSTALLATION OF YOUR NECTRE
WOOD HEATER BE CARRIED OUT BY A QUALIFIED INSTALLER.
WARNING: THE APPLIANCE AND FLUE SYSTEM SHALL BE
INSTALLED IN ACCORDANCE WITH AS/NZS 2918 AND THE
APPROPRIATE REQUIREMENTS OF THE RELEVANT BUILDING
CODE OR CODES.
WARNING: APPLIANCES INSTALLED IN ACCORDANCE WITH
THIS STANDARD SHALL COMPLY WITH THE REQUIREMENTS
OF AS/NZS 4012 & AS/NZS 4013 WHERE REQUIRED BY THE
REGULATORY AUTHORITY, I.E. THE APPLIANCE SHALL BE
IDENTIFIABLE BY A COMPLIANCE PLATE WITH THE MARKING
‘TESTED TO AS/NZS 4012 & AS/NZS 4013’.
ANY MODIFICATION OF THE APPLIANCE THAT HAS NOT BEEN
APPROVED IN WRITING BY THE TESTING AUTHORITY IS
CONSIDERED TO BE IN BREACH OF THE APPROVAL GRANTED
FOR COMPLIANCE WITH AS/NZS 4012 & AS/NZS 4013.
CAUTION: MIXING OF APPLIANCE OR FLUE-SYSTEM
COMPONENTS FROM DIFFERENT SOURCES OR MODIFYING
THE DIMENSIONAL SPECIFICATION OF COMPONENTS MAY
RESULT IN HAZARDOUS CONDITIONS. WHERE SUCH ACTION IS
CONSIDERED, THE MANUFACTURER SHOULD BE CONSULTED
IN THE FIRST INSTANCE.
CAUTION: CRACKED AND BROKEN COMPONENTS, EG. GLASS
PANELS OR CERAMIC TILES, MAY RENDER THE INSTALLATION
UNSAFE.
THE INSTALLATION INSTRUCTIONS IN THIS MANUAL
APPLY TO THE NECTRE 1 WOOD HEATER MODELS. MK LE
THEY HAVE BEEN TESTED FOR EMISSIONS AND
EFFICIENCY AND COMPLY ACCORDING TO AS/NZS 4012 &
AS/NZS 4013.
2
1.2. FITTING REAR HEAT SHIELD
Before working out the posion of the heater and the relevant
clearances to combusble surfaces, t the rear outer heat
shield with the curved end at the top and spacers between
the inner heat shield:
1) On the rear of the heater, there are four 32mm long PK
screws xing the outer heat shield, upside-down, to the
inner heat shield. Remove the screws and the outer heat
shield.
2) Rotate the outer heat shield 180 degrees so that the
curved end is on top and angled towards the front of the
heater.
3) A plasc packet with four 20mm long tubular spacers will
be inside the heater. Re-locate the four 32mm long PK
screws through the original holes in the outer heat shield,
slide a spacer over each screw, and re-fasten to the inner
heat shield.
1.3. INSTALLING THE HEATER
1.3.1. Posioning the Heater
Review the necessary clearances specied in this secon
before considering where to posion the heater.
Also check the praccability of installing the ue system in
relaon to any obstrucng roof beams before posioning the
heater.
The clearance distances can only be reduced if the
surrounding walls are made of non-combusble material such
as stone, brick or concrete. If non-combusble material,
distance can be reduced to 100 mm. Alternavely, shielding of
the wall(s) can reduce clearances (refer to next secon for
more detail).
Clearances to combusble surfaces vary depending on the
type of ue shielding used.
1.3.2. Standard Installaon
Dimensions given in the table and image below represent the
minimum clearance (in millimetres) to combusble materials.
A = Side clearance
B = Rear clearance
C = Minimum oor protector depth from door opening
Termékspecifikációk
| Márka: | Nectre |
| Kategória: | Fűtő |
| Modell: | MK1 LE |
Szüksége van segítségre?
Ha segítségre van szüksége Nectre MK1 LE, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek
Útmutatók Fűtő Nectre
13 Augusztus 2024
13 Augusztus 2024
13 Augusztus 2024
12 Augusztus 2024
12 Augusztus 2024
12 Augusztus 2024
11 Augusztus 2024
4 Augusztus 2024
5 Július 2024
Útmutatók Fűtő
- Fűtő Master
- Fűtő Beurer
- Fűtő Wanders
- Fűtő Infiniton
- Fűtő Ecoteck
- Fűtő Parkside
- Fűtő Ferroli
- Fűtő IXL
- Fűtő Scarlett
- Fűtő Concept
- Fűtő CaterChef
- Fűtő Enders
- Fűtő Real Flame
- Fűtő Burley
- Fűtő Truma
Legújabb útmutatók Fűtő
6 Április 2025
4 Április 2025
30 Március 2025
30 Március 2025
30 Március 2025
30 Március 2025
27 Március 2025
27 Március 2025
27 Március 2025
27 Március 2025