Használati útmutató Neff T26TA49N0

Neff sütő T26TA49N0

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Neff T26TA49N0 (9 oldal) a sütő kategóriában. Ezt az útmutatót 2 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/9
1
*8001232562* 8001232562 011109
de Montageanleitung
el Οδηγίες εγκατάστασης
en Installation instructions
es Instrucciones de montaje
fr Notice d'installation
hu Telepítési útmutató
it Istruzioni d'installazione
nl Installatie-instructies
pl Instrukcje montażu
pt Instruções de instalação
ro Instrucţiuni de instalare
ru Инструкция по установке
tr Kurulum talimatları
1
2
6
28
ID Gas Nz Qn (kW) m3/h g/h Z (mm) Y (mm) M
G20/20mbar 72 1,10 0,105 - - - B
G20/25mbar 65 1,10 0,105 - - - B
G25/20mbar 79 1,10 0,122 - - - B
G25/25mbar 78 1,10 0,122 - - - B
G25.1/25mbar 78 1,10 0,122 - - - B
G25.3/25mbar 78 1,10 0,119 - - - B
G30/29mbar 53 1,10 - 80 - - A
G30/37mbar 53 1,10 - 80 - - A
G30/50mbar 48 1,10 - 80 - - A
G31/37mbar 53 1,10 - 79 - - A
G20/20mbar 93 1,90 0,181 - - - B
G20/25mbar 91 1,90 0,181 - - - B
G25/20mbar 105 1,90 0,211 - - - B
G25/25mbar 104 1,90 0,211 - - - B
G25.1/25mbar 104 1,90 0,21 - - - B
G25.3/25mbar 104 1,90 0,21 - - - B
G30/29mbar 70 1,90 - 138 - - A
G30/37mbar 68 1,90 - 138 - - A
G30/50mbar 60 1,90 - 138 - - A
G31/37mbar 70 1,90 - 136 - - A
G20/20mbar 125 2,80 0,267 - - - B
G20/25mbar 109 2,80 0,267 - - - B
G25/20mbar 141 2,80 0,31 - - - B
G25/25mbar 118 2,80 0,31 - - - B
G25.1/25mbar 118 2,80 0,31 - - - B
G25.3/25mbar 118 2,80 0,304 - - - B
G30/29mbar 83 2,80 - 203 - - A
G30/37mbar 82 2,80 - 203 - - A
G30/50mbar 74 2,80 - 203 - - A
G31/37mbar 83 2,80 - 200 - - A
G20/20mbar 1 - 141
2 - 58
4,20 0,4 - 7,5 open B
G20/25mbar 1 - 132
2 - 54
4,20 0,4 - 3 4,5 B
G25/20mbar 1-156
2-63
4,20 0,466 - 1,5 1,5 B
29
13
Electrical connection
¡This appliance is type Y: The connection cable
must only be replaced by technical customer ser-
vice and not by the user. The cable type and the
minimum cross section must be respected.
¡The hobs are supplied with a power cord with or
without a plug.
¡Only connect appliances that are fitted with a plug
to a correctly installed socket with protective earth
conductor.
¡If the plug is not accessible to the user, an all-pole
isolating safety switch with a minimum contact
opening of 3 mm must be provided.
→Fig. 12
Converting the gas type
If the country's regulations allow, this appliance can
be adapted to other types of gas, if these are listed
on the rating plate.
You can find the right parts in the bag that is sup-
plied with the appliance or you can obtain them from
customer service. The →Fig. 29 shows the right
combination for the relevant burner and gas type.
Economy burner
Standard-output burner
High-output burner
Dual-wok multi-crown burner
¡1-Outer flame
¡2-Inner flame
Tools
Contact technical customer service to purchase the
relevant tools.
Removal lever 483196
Removing the upper part of the appliance (glass
plate with cut-out profiles)
1. Remove the pan supports, burner caps, distribut-
ors and rotary knobs.
2. Undo the screws on the burners.
→Fig. 13
3. Move the removal lever under the metal cut-out
profile into the area marked for the hob model
and loosen the front clip fastener.
→Fig. 14
Only use the lever under the cut-out profiles or the
metal frame of the hob.
4. Carefully lift the glass plate with the cut-out pro-
files to release the rear clip fastener.
Removing the circuit board
Tip:The circuit board is secured to the holder by
fastening pins at the sides and in the middle. Push
the fastening pins carefully without damaging them.
If one of the pins breaks, the entire holder must be
replaced.
ATTENTION!
The circuit board can be damaged by improper
handling.
▶
▶
▶
▶▶ Handle the circuit board carefully.
▶
▶
▶
▶▶ Use anti-static shields or hold the circuit board at
the edges.
▶
▶
▶
▶▶ Never touch the surfaces of the circuit board on
which there are components or conducting tracks.
1. Undo the fastening pins on one side.
2. Release the fastening pins in the middle by press-
ing on them from both sides with your fingers.
3. Undo the fastening pins on the other side and re-
move the circuit board.
→Fig. 15
Adjusting the taps
Requirement:The upper part of the appliance and
the circuit board are removed.
→"Removing the upper part of the appliance (glass
plate with cut-out profiles)", Page13
→"Removing the circuit board", Page13
1. Remove the cylindrical parts and springs from the
fittings spindle.
2. When adjusting the bypass screws (M), refer to
the →Fig. 29 .
‒A: Firmly tighten the bypass screws.
‒B: The bypass screws must be flush with the fit-
ting.
→Fig. 16
Replacing the nozzles
▶
▶
▶
▶▶ Replace the nozzles using the appropriate wrench
and tighten them carefully to guarantee the seal.
→Fig. 17
Ensure that the nozzle does not become detached
during removal or fastening.
Replacing the outer flame nozzle on the multi-
crown burner
Requirement:The upper part of the appliance has
been removed.
→"Removing the upper part of the appliance (glass
plate with cut-out profiles)", Page13
1. To gain access to the main nozzle, loosen the
fastening screw and pull the sleeve back.
→Fig. 18
2. Remove the nozzle by turning it anti-clockwise
and screw in the new outer flame nozzle .
→Fig. 19
3. Set the spacing of the adjustment sleeve for the
air supply to dimension Z, as shown in the →Fig.
29 .
→Fig. 20
4. Tighten the fastening screw.
→Fig. 21
Replacing the inner flame nozzle on the multi-
crown burner
Requirement:The upper part of the appliance has
been removed.
→"Removing the upper part of the appliance (glass
plate with cut-out profiles)", Page13
1. Unscrew the tube by applying pressure to the
sleeve in the opposite direction to hold it in place
and pulling the tube out of the sleeve .
→Fig. 22
2. Remove the sleeve.
→Fig. 23
3. Remove the inner flame nozzle from the sleeve
and screw in the new nozzle.
→Fig. 24
4. Screw the sleeve and the tube back into their ori-
ginal position.
5. Depending on the type of gas, it may be neces-
sary to set the spacing to that specified in the
→Fig. 29 for the value Y using the clip for adjust-
ing the air supply.
→Fig. 25
Reinstalling the appliance
▶
▶
▶
▶▶ Install the appliance components in reverse order.
Checking if equipment is working
1. Check that turning the rotary knob between the
position for maximum power and the position for
minimum power does not cause the burner to go
out or result in backfire.

Termékspecifikációk

Márka: Neff
Kategória: sütő
Modell: T26TA49N0

Szüksége van segítségre?

Ha segítségre van szüksége Neff T26TA49N0, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók sütő Neff

Neff

Neff B64CS71N0 Útmutató

28 Március 2025
Neff

Neff C24FS31N0 Útmutató

28 Március 2025
Neff

Neff B64VS31N0 Útmutató

28 Március 2025
Neff

Neff B24FS33N0 Útmutató

28 Március 2025
Neff

Neff B18M42N3 Útmutató

22 Március 2025
Neff

Neff b 1583 w s n Útmutató

16 Március 2025
Neff

Neff E 1420 S W N Útmutató

15 Január 2025
Neff

Neff T 15B8 N0 Útmutató

14 Január 2025
Neff

Neff C17DR00N0 Útmutató

12 Január 2025
Neff

Neff B64FT33N0 Útmutató

4 Január 2025

Útmutatók sütő

Legújabb útmutatók sütő

Whirlpool

Whirlpool akp 234 na 02 Útmutató

10 Április 2025
Candy

Candy FCP405X Útmutató

10 Április 2025
Premiere

Premiere EBC 23558 E Útmutató

10 Április 2025
Gram

Gram KKI 8544-90 T Útmutató

10 Április 2025
KitchenAid

KitchenAid KHDD2 38510 Útmutató

10 Április 2025
Stoves

Stoves Richmond 1000DFT Útmutató

10 Április 2025
Küppersbusch

Küppersbusch EEH615.0 Útmutató

10 Április 2025
Ariston

Ariston FM 51 Útmutató

10 Április 2025
Siemens

Siemens HB23A1520S Útmutató

9 Április 2025
Whirlpool

Whirlpool akp 237 Útmutató

9 Április 2025