Használati útmutató OSD Audio Speaker Selector 12

Olvassa el alább 📖 a magyar nyelvű használati útmutatót OSD Audio Speaker Selector 12 (1 oldal) a kapcsoló kategóriában. Ezt az útmutatót 23 ember találta hasznosnak.

TSM8/ TSM12

Autoformer Based Speaker Selector

Instruction Manual

AUDIO

OSD

Thank you for giving OSD AUDIO the chance to earn your business! We are condent you will nd that OSD oers an outstanding combination of performance

and value in everything we make. To ensure you get the most out of your new TSM8/ TSM12, please take a moment to read this manual before you get started.

OSD Audio • 1405 t • ea • A • 92821 •• Tel (562) 697-2600 • Pioneer SBrC www.osdaudio.com Fax (562) 697-2668

1. Connections

To connect the amplifiers/receivers to the speaker selector, remove the AMP A/B connector by firmly pulling it out of its 8-pole socket. Strip ” of insulation from the end 1/4

of each wire. Tightly twist the end of each wire until no frayed ends remain. Insert each wire into the appropriate hole on the removeable terminals (matching up the

polarity). Use a small screwdriver to tighten each wire into the AMP A/B connector. Insert the connector plug into the socket and lock in place Be sure not to reverse .

these connections or the will not functionproperly. TSM12 /TSM8 Follow the same procedureto connect each ir spaofpeakers to pthe apropriate speaker connector terminal,

observi pper channngroel and polarity. If external volume control s are used, t sconnecpeaker wire rfromtheappopriate speakerconnectoronthe TSM12/ TSM8to the volume

corontl input. r tSpeakeconnecions scanupport ltie rs muplspeakerpaiwired inpa rallel or series, providedthei r combimined pedncea is a minimumof 4 s.ohm

2. Operation

To u fe oensre saperation of theamplifie r, animpedance level must fi rst beselected usingthe rotary switch llabeed speaker pair tlocaedon the of rearthe unit. This switch should

be to e l nsetthtotaumspber of eakerpair s i bengconnecedt to theun it. Set the switch fbased on theollowingconditions:

If thempli afier andthe spea kersare both 4 t tohm or 8 ohm, seheota rry switch to thenu mberofpair of speakers e connectedtothTSM12 /TSM8.

If thempli afier is 8 tohmandhespeakers are 4 tohm,sethe rotary switch to TCE WIthe numbe r of ir spaofpeakerconnec eds t to TSM12 /TSM.8

If e r 4 othamplifieishms and akethe spers are 8 oh, set the rory switch to HAmstaLF the nu mber ofpai r of speakeconnected to the rs TSM12 /TSM8.

After ng settitheproperimpedancelevel, thespeakers can be turned on and off in any combination.

Sch wwitbeteen th e A and B pamlifiers, the pushAMP A / AMP B tn lobutocaedt onthe fr .ont panel

3.SettingSystem Volume

It is important toproperlyadjustan impedance-matchingsystemto avoid distortion orDC clipping (DC voltagewillbeproduce d from aanmpifielr wthatis overorkedorthat hasan

improper lo ad). These can cause an amplifierrece/iver to go intoprotection,an d can ocauseautofrmers on volume controlstoheatup, damag ing sysemt compoentns. To set up

the system, theamplifier/rece iver volume d shoulbeat its lowest setting, andthein- wall/selector volume corntolsho uld st s beatthehigheetting.Slowlyadj ust the

amplifieivr/receer volume to a vleel that is the aacceptableformplifier to proce duwithoutclipping .

100 Watts per channels RMS continuous

200 Watts per channel average

300 Watts per channel peak

17” x 7.1” x 2.9”

Up to 14 Gauge wire

2 Years

Listening Zones:8 (TSM8)12 (TSM12)

Power:

Dimensions: L x W x H:

Cable Gauge:

Warranty:

100 Watts per channels RMS continuous

200 Watts per channel average

300 Watts per channel peak

17” x 7.1” x 2.9”

Up to 14 Gauge wire

2 Years

AUDIO

OSD

7-8

6

53-4

2

1

Number of

Speaker Pair

AMPLIFIERS

SPEAKERS

AMP AAMP B

AMPLIFIERS

PAIR1PAIR2PAIR3

PAIR4

PAIR5PAIR6PAIR7

PAIR8

Termékspecifikációk