Használati útmutató Paasche H-100D

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Paasche H-100D (2 oldal) a nincs kategorizálva kategóriában. Ezt az útmutatót 22 ember találta hasznosnak.

INSTRUCTIONS AND PARTS LIST H AIRBRUSH 8/06/2019

H Model Airbrush

Single Action–External Mix–Siphon Feed

Instruction Manual & Replacment Parts

OPERATING INSTRUCTIONS:

Approximate Working Pressures:

• 20lbs.orLess:Stippleandgranulatede󰀨ects,pressurewillvarywithviscosityofuid.

• 20to30lbs.:Mediumconsistencywatercolors,inks&dyes.

• 30lbs. or More:Heavyuids,acrylics,reducedlacquers,varnishes,paintsorceramicglaze.

Sizes:

• H-1(.45mm)HeadandHC-1-3Aircapforlightuids.

• H-3(.64mm)HeadandHC-1-3Aircapformediumuids.

• H-5(1.06mm)HeadandHC-5Aircapforheavieruids.

1.Attach hose to airsupplyand allow airto blow afew seconds. Shut o󰀨 beforeattaching to Airbrush. This procedurewill

removedirtfromairlineandhose.

Caution: Hold rmly and point away from face.

2. Attachhosecouplingtotheairbrush.

3.AttachColorCuporBottletoHN-1-3,or5Needlebyexertingarmtwistingmotiontottaperedtubesecurelyintotapered

Needleinlet.

4. FillColorCuporBottle1/2to3/4full.Useeyedropperorbrushforaddingsmallamountsofcolortometalcolorcup.Whenusing

ColorBottle,ventholemustbekeptopen.

5.ToSpray,holdAirbrushlikeapencilcomfortablybetweenthumbandforengerusingmiddlengerasaguideandsupport.

Likewriting,holdforengereasilyonH-155FingerButtonandPresstoopenairvalve.

6.Regulate volume ofcolor and size of sprayby rotatingHT-1,3 or 5 Tipclockwise to increase andcounter clockwise to

decreaseowofcolor.

7.StippleAdjustment:Reducingtheairlinepressureistheeasiestmethodusedwhencreatingastipplede󰀨ectwiththeairbrush.

Pressurecanbereducedbyusinganyofthefollowingitems:3ANeedleValveinstalledontheH-128AValveCasingofthe

AirbrushorbyusingtheR-75AirRegulatorandreducingthepressure.

8.Toadjustforheavieruids,turntipwideopen,loosensetscrew,slideneedlebacktoobtainbetterow.

CARE AND CLEANING:

1.Pouranyremainingcolorbackintoitsoriginalcontainer.

2.WipeColorCuporBottleclean,usingclothmoistenedwithpropersolvent.

3.HoldAirbrushatadownwardangleandputafewdropsofsolventthroughColorAdjustingPartAssembly.Toushoutthe

remainingcolorintheHColorAdjustingPartAssembly,applypressuretothe H-155FingerButton.

4.ApplyatinydabofVaselinetotheHColorAdjustingPartandHC-Aircapthreadseverytwoorthreemonthstopreventcolor

buildupandconsequentfreezingoftheColorAdjustingPartAssemblyandAircap.

HOW TO OPEN CLOGGED FLUID PASSAGES:

1.AgitatecolorinBottleAssemblybyplacingngermomentarilyoverHC-AircapwhileairispassingthroughtheAirbrush.This

willblowcolorbackintobottlethusopeningcloggeduidpassages.Do not do this with open cup as color may blow out

of cup.

2.ShouldH-1,3or5ColorAdjustingPartAssemblybecomeclogged,loosenH-153SetScrew,unscrewHT-1,3or5Tipfrom

HNNeedle,gentlypullbackthroughball-shapedsupportandremoveTip.

3.CleanPartscarefully,usingnothingharderthanawoodentoothpick.

4. Toreassemble,reversethisprocedure,makingsuretheshoulderoftheNeedleseatsupagainstball-shapedsupport.

5.Iftheneedleandtiparecompletelyclogged,soakinaclosedbottleofpropersolventuntilclean.

INTRODUCTION:

Paasche®H model Airbrush features machined BrassBody and Nickel

SilverColorPart, simplicityofdesign andeaseinoperation.Theair and

colorfeeds are independentand adjustable togive axed line, shadeor

stipplee󰀨ect.

For Multi-Language Manuals Go To: www.paascheairbrush.com

Termékspecifikációk