Használati útmutató Philips MatchLine 32FD9954

Philips Monitor MatchLine 32FD9954

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Philips MatchLine 32FD9954 (17 oldal) a Monitor kategóriában. Ezt az útmutatót 2 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF

Oldal 1/17

CORRECTLY INCORRECTLY

Note: the enclosed template can be used for general positioning only

(fig. 1).

Mounting to sheetrock wall

Note: Bracket can only be used with standard 16" spaced wood wall

studs.

Bracket must be positioned so that the bracket is fastened firmly to

studs at each end.

All required hardware is included.

Note: Because the Receiver Unit’s power cord is 6’, when determining the

Display Unit mounting location, the distance to the nearest AC power

outlet must be considered.

&Determine desired location to mount Display Unit.

Within this area, locate the two 16.54" spaced wall studs that must

be used as the Wall Bracket mounting location. (fig. 1 and 2)

éWith the Wall Bracket held in place, ensure it is properly leveled.

Then, mark where the four holes must be drilled. (fig. 2)

Note: Use only the holes in Bracket.

“Remove the Wall Bracket, and using a 13/64" wood drill bit, drill the

four holes. (fig. 3)

‘Reposition the Wall Bracket, and with four lag bolts (fig. 4), secure

into place.Tighten with 13mm or 1/2" socket wrench. (fig. 5)

Note: Do not use plastic wall anchors with these lag bolts.

Note: Lag bolts must be fastened and centered securely into the stud.

Mounting Wall Bracket

fig. 1

fig. 2

420mm /16,54"

60,5mm / 2.38"

fig. 3

fig. 4

fig. 5

English

Mounting to concrete wall

&Determine desired location to mount Display Unit. Use the enclosed

template for alignment purposes. (fig. 1)

éWith the Wall Bracket held in place, ensure it is properly leveled.

Then, mark where the four holes must be drilled. (fig. 4)

“Remove the Wall Bracket, and using a 5/8" masonry drill bit, drill the

four holes. (fig. 2)

‘Insert a concrete anchor (with bolt) into each hole.

(Firmly tighten each bolt.Then, remove the bolts.

§Reposition the Wall Bracket, and with the four bolts (and washers),

secure into place.

Mounting to concrete block wall

&Determine desired location to mount the Display Unit.

Within this area, position the Wall Bracket so that the four end

mounting holes are located over the cavities of the concrete blocks

(refer to Figure 1)

éWith the Wall Bracket held in place, ensure it is properly leveled.

Then, mark where the four holes are to be drilled.

Note: Use only the four outside or end holes in the Bracket.

“Remove the Wall Bracket and reconfirm that the marks made in the

previous step are located in the cavities of the concrete blocks. Re-

locate the marks as required to ensure that they are in the cavities

of the concrete blocks.

‘With a 1/2” masonry drill bit, drill the four holes.

(Hinge the plastic legs of the toggle bolt into the channel of the metal

end of the toggle bolt so it can fit into the 1/2” hole drilled in the

wall (refer to Figure 2).

§Insert the toggle bolt into the hole in the wall and push it in until it

is in the cavity of the block.

èWith the plastic pull ring of the toggle bolt, pull the metal end of the

toggle bolt firmly against the back of the cavity of the concrete block

(refer to Figure 3).

WASHER

Cavities In Block

Fig. 1

Fig. 2

Fig. 3

!While holding the plastic pull ring, slide the plastic retaining sleeve

towards the wall until it fits into the hole in the wall. This will hold

the toggle bolt in the wall while the Wall Bracket is mounted (refer

to Figure 4).

Push down on the lower plastic leg of the toggle bolt and break it off

flush with the wall (refer to Figure 5).

Push up on the upper plastic leg of the toggle bolt and break it off

flush with the wall (refer to Figure 6).

Install the remaining 3 toggle bolts in the remaining holes the same

way that the first one was installed.

Position the Wall Bracket in place and install the four 1/4-20 bolts,

including washers, in each of the outside corner holes. Do not

tighten completely (refer to Figure 7).

Confirm that the Wall Plate is level, then tighten the bolts securely

(refer to Figure 8).

Mounting to metal stud wall

&Determine desired location to mount the Display Unit.

Within this area, locate the two 16.54” spaced metal wall studs that

must be used as the Wall Bracket mounting location.

éLocate the center of both wall studs at the height that the Wall

Bracket is to be mounted.

“With the Wall Bracket held in place, ensure it is properly leveled.

Then, mark where the four holes are to be drilled.

Note: Use only the four outside or end holes in the Bracket

(refer to Figure 1).

‘Remove the Wall Bracket and reconfirm that the marks made in the

previous step are located in the center of the metal wall studs. Re-

locate the marks as required to ensure that they are in the center of

the metal wall studs (refer to Figure 2).

Metal Wall

Studs

Fig. 1

Holes Centered In

Metal Wall Studs

Fig. 2

Fig. 4

Fig. 5

Fig. 6

Fig. 7

Fig. 8

Termékspecifikációk

Márka:	Philips
Kategória:	Monitor
Modell:	MatchLine 32FD9954

Szüksége van segítségre?

Ha segítségre van szüksége Philips MatchLine 32FD9954, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek

Az Ön neve*

Az Ön e-mail címe*

Írja ide kérdését

Útmutatók Monitor Philips

Philips 221V8LB Útmutató

4 Április 2025

Philips Evnia 49M2C8900LA Útmutató

28 Március 2025

Philips 25M2N5200U Útmutató

26 Március 2025

Philips 150S3F Útmutató

24 Március 2025

Philips Brilliance B-line 241B4LPYCS Útmutató

24 Március 2025

Philips Momentum 242M7 Útmutató

20 Március 2025

Philips 27E1N1600AM Útmutató

17 Március 2025

Philips S Line 222S9 Útmutató

14 Január 2025

Philips 27B2U6903 Útmutató

3 Január 2025

Philips Envia 27M1N3500LS Útmutató

29 December 2024

Útmutatók Monitor

Legújabb útmutatók Monitor

NEC SpectraView II Útmutató

9 Április 2025

Asus VA279QGS Útmutató

9 Április 2025

Acer EV227Q Útmutató

9 Április 2025

BenQ PD3226G Útmutató

8 Április 2025

BenQ DesignVue PD2730S Útmutató

8 Április 2025

Samsung LH65QETEPGC Útmutató

5 Április 2025

Gigabyte MO27U2 Útmutató

5 Április 2025

PureTools PT-SCREEN-100 Útmutató

2 Április 2025

Extron TLS 1025M Útmutató

2 Április 2025

Viewsonic VG2752-2K Útmutató

30 Március 2025