Használati útmutató Pioneer DVR-112D

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Pioneer DVR-112D (3 oldal) a nincs kategorizálva kategóriában. Ezt az útmutatót 7 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Oldal 1/3
D I RIVE NSTALLATION
IN N A INSTANT
Step 1 – Prepare the Computer
1) Turn OFF the computer and disconnect the power cord.
2) Remove the bezel and the open drive bay cover from the computer’s front panel.
Note: Your computer may be a tower
model as shown on the left or a
desktop model as shown below. This
drive works in either PC model style.
Step 2 – Prepare the Drive
3) Attach slide rails to the drive if required for your drive model.
Slide rails are sold separately through computer retailers.
4) Position the drive close to the open computer bay.
Horizontal Installation Vertical Installation
Step 3 – Connect the Cables
5) Connect the power cable from the computer to the drive.
Pay close attention to the polarity of the cable.
6) Connect the IDE cable to the drive.
C onfirm that Pin 1 on the drive corresponds to Pin 1 on the cable.
7) Connect the drive’s audio output to the sound card if one is present.
D I RIVE NSTALLATION
IN N A INSTANT
Step 4 – Finish the Installation
8) Place the mounting screws in the appropriate holes and tighten by hand.
When mounting screws are loose, vibrations from the spinning disc may cause a ripping sound.
9) Replace the bezel and power ON the computer.
Setting the Jumper For Use in a Master/Slave PC
If you have a Master/Slave type of computer, you probably have two IDE channels, Primary and Secondary. The hard
drive is using the Primary IDE channel and any drives are using the Secondary channel. Install this drive as the Master
device on the Secondary channel and any other devices as Slaves o this new drive. Follow the directions below to
change your older drives or other equipm device.
2) Remove the drive from the drive bay.
3) Use your fingers or
t
ent on the Secondary channel to a Slave
1) Disconnect the following drive cables in the order listed below.
Power cable
IDE cable
Audio cable
a tool to move the jumper to the new setting.
4) Return the drive to the drive bay.
5) Reconnect the cables in the reverse order, Audio, IDE then Power.
Jumper: (jumpered = ON; no jumper = OFF)
Set the jumper to select the drive type for your computer.
Pin Name Function
1 MA on Drive set to Master mode
2 SL on Drive set to Slave mode
3 on Drive set to Cable Select mode CS
4 Reserved
5 Reserved
Slave Cable Select Master
Setting the Jumper For Use in a Cable-Select PC
Some computer pport a e n f your PC uses Cable Select then all devices
need to be set to Cable Select as well. Also, the IDE cable must be designed for Cable Select communication.
Simply position the jumper r Cab d install the drive according to the instructions beginning on the opposite
ide of this paper. No other changes are required when usin ble Select computers.
Do Not jumper the drive to Cable Select unless your PC uses this method.
s su a dat xcha ge method called Cable Select. I
fo le Select an
s g Ca

Termékspecifikációk

Márka: Pioneer
Kategória: nincs kategorizálva
Modell: DVR-112D

Szüksége van segítségre?

Ha segítségre van szüksége Pioneer DVR-112D, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek




Útmutatók nincs kategorizálva Pioneer

Útmutatók nincs kategorizálva

Legújabb útmutatók nincs kategorizálva

MOZA

MOZA SR-P Útmutató

10 Április 2025
CaterChef

CaterChef 445001 Útmutató

9 Április 2025
IFM

IFM E40581 Útmutató

9 Április 2025
Livn

Livn Bolt Útmutató

9 Április 2025
Livn

Livn Beats Útmutató

9 Április 2025
IFM

IFM O3R252 Útmutató

9 Április 2025