Használati útmutató Pioneer S-RS3SW

Pioneer hangszóró S-RS3SW

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Pioneer S-RS3SW (2 oldal) a hangszóró kategóriában. Ezt az útmutatót 12 ember találta hasznosnak és 6.5 felhasználó értékelte átlagosan 4.6 csillagra

Letöltés PDF

Oldal 1/2

ACCESSORY ITEMS

• Power cable

Taiwan, Mexico, Middle Latin America models x 2

All other models x 1

• Operating instructions

FEATURES

n 150 W (Taiwan model)/180 W (all other models) (RMS) power with AB

class amplifier that serves audio and video software playback such

as Dolby Digital with a wide dynamic range.

n Equipped with 30 cm driver

n Crossover frequency can be set to 50 Hz to 200 Hz.

IN COMBINATION WITH SPEAKERS

The frequency characteristics of the S-RS3SW combined with small-

size speakers are shown below. As shown in these figures, the low

frequency range is improved.

• These special characteristics are obtained in an echoless chamber.

The effect of an additional S-RS3SW in an ordinary listening room is

better than the chart indicates when positioned adequately.

• With playback of Dolby Digital, establishment of a special channel

for the subwoofer is recommended; and with playback of LFE (Low

Frequency Effect: sound effect like the rumbling of the earth, whose

purpose is to intensify the force of the video), the S-RS3SW is

especially effective.

INSTALLATION

Speaker Installation

• Subwoofer Installation Criteria

1 Left speaker

2 Right speaker

3 Recommended

installation range

for the subwoofer

4 Listening position

The subwoofer plays back the bass in monaural, making use of the fact

that the human ear is not very sensitive to the direction of low-pitched

sound. Because of this, the subwoofer can be installed almost

anywhere. If it is installed too far away, however, the sound from the

other speakers may become unnatural.

• An example of speaker positioning

1 Front left speaker

2 Center speaker

3 Front right speaker

4 Subwoofer

5 Listening area

6 Rear left speaker

7 Rear right speaker

NOTES:

• Position the left and right channel speakers at equal distances from

the TV set and approximately 1.8 meters from each other.

• Install the center speaker above or below the TV so that the sound of

the center channel is localized at the TV screen.

• The rear (surround) speakers are most effective when installed in

parallel locations directly to the side, or slightly behind, the listener,

at a level about 1 meter above the listener’s ears.

Installation Precautions

• Do not attach the subwoofer to the wall or ceiling. They may fall off

and cause injury.

• Install the unit in a well-ventilated location where it will not be

exposed to high temperatures and high humidity.

• Do not place the unit near stoves or other heating equipment or at

locations exposed to direct sunlight, as these can have an adverse

effect on the cabinet and internal components. Also, do not install

the unit where there is too much dust or high humidity, as these can

cause malfunctioning or breakdowns. (Avoid cooking tables and

other locations where the unit would be exposed to heat, steam and

soot.)

• Do not place heavy or large objects on top of the speaker. Doing so

could provoke the speaker to fall, causing damages or bodily injury.

If speakers fall from their installation locations, they may suffer

irreparable cracks in their finish.

• Keep the unit away from devices such as cassette decks which are

sensitive to magnetic fields.

• Do not place the speaker on an unstable surface, as doing so may

cause the speaker to fall and cause damage or bodily injury.

• Do not place cups, glasses, or other containers with fluids on top of

the units, since the units may be damaged if the liquid spills.

• The installation location selected should have a sturdy floor surface.

Mounting the speaker on a long-pile carpet should be avoided, since

the carpet may touch the driver’s diaphram, causing distorted

sound.

• Please install this unit away from the antenna cable of the tuner, as

noise can be caused with installation close to the antenna cable. In

such a case, use this unit at a position away from the antenna and

the antenna cable, or when playback of extra bass is not required,

switch off the power for this unit.

Small-size s eake s + S-RS3SWp r

Small-size s eakep r

FREQUENCY (Hz)

RESPONCE (dB)

1 2

2 3

6 7

CAUTION:

When installing the center speaker on top of the TV, be sure to

secure it with tape or some other suitable means.

Otherwise, the speaker may fall from the TV due to external shocks

such as earthquakes, and it may lead to endangering those nearby

or damaging the speaker.

The subwoofer is not magnetically shielded and so should not be

placed near a TV or monitor. Magnetic storage media (such as

floppy discs and tape or video cassettes) should also not be kept

close to the subwoofer.

MAINTENANCE OF EXTERNAL SURFACES:

• Clean the surface by wiping with a soft, dry cloth.

• When the surfaces are very dirty, wipe with a soft cloth dipped in

some neutral cleanser diluted five or six times with water, and

wrung out well, and then wipe again with a dry cloth. Do not use

furniture wax or cleaners.

• Never use thinners, benzine, insecticide sprays and other

chemicals on or near this unit, since these will corrode the

surfaces.

PANEL FACILITIES

FRONT PANEL

REAR PANEL

1 Power Indicator (POWER ON)

Lights green when the power has been switched ON.

NOTE:

• If you are planning on switching the unit OFF for a long period of

time, make sure to check that the indicator light has gone out after

switching OFF.

2 Power switch (POWER)

Switches the subwoofer between ON and OFF.

3 Volume knob (VOLUME)

Sets the subwoofer volume.

• Turn the knob slowly from the MIN position.

• With this unit, the bass level can be independently set, so do not

turn up the bass on the AV amplifier.

4 Crossover knob (CROSSOVER)

When using the subwoofer, set the upper frequency limit for the

subwoofer (50 Hz

to 200 Hz

) so that it complements the output from

your other speakers.

When using the bass management features of an AV receiver, set to

BYPASS ON

in order to use the low-pass

filter of the AV receiver for

high quality sound.

5 Bypass switch (BYPASS)

When set to ON, the audio signal is routed directly to the woofer unit,

bypassing the amplifier’s filter.

6 Phase switch (PHASE 0º /180º)

When set to 180º, the output phase becomes the reverse of the input

signal, and when set to 0º, it is in the same phase as the input signal.

• Normally, the switch is set to 0º.

But when the sound connection between the subwoofer and the

left and right speakers sounds

unnatural, try switching to

180º

and set the switch in the position where the sound is natural.

• When using two or more subwoofers together, make sure that the

phase switch of all of them are set to the same position.

7 Line Level Input terminal (LINE LEVEL INPUT)

Connect to the SUBWOOFER PREOUT terminal of an amplifier or

receiver, with a RCA plug cord.

8 Line Level Output terminal (LINE LEVEL OUTPUT)

Used for connecting other equipment through the amplifier. The

signal output from this jack is not affected in any way by the settings

of the various controls on the unit.

9 AC IN

• Connect the power cord to the powered subwoofer unit’s AC IN.

• Connect the power cord to a AC socket.

CONNECTIONS

Before making or changing any connections, switch off the power

and disconnect both this unit and the amplifier/receiver from the

AC outlet.

LINE LEVEL CONNECTION

This connection is for an amplifier or receiver equipped with a

SUBWOOFER PREOUT terminal. Connect to the LINE LEVEL INPUT

terminal on this unit, using a RCA plug cord.

NOTE:

• When connected to the PREOUT terminal for surround center

channel on the amplifier or receiver, the bass is heard only on the

center channel, so it will be insufficient.

OPERATION

For details regarding operating part functions, refer to PANEL

FACILITIES above.

1. Turn the POWER switch (2) ON.

• If the unit’s power cord is connected to a switched AC outlet on

the amplifier or receiver and the switch is left ON, the unit can be

turned ON/OFF together with the amplifier or receiver.

• If the unit cannot be connected to the amplifier or receiver, turn

the power to the amplifier or receiver ON before turning the power

to the unit ON. When turning the power OFF, turn the power to the

unit OFF before turning the power to the amplifier or receiver OFF.

2. Operate the amplifier or receiver and adjust the volume of the

other speakers.

3. Adjust the volume of the bass with the VOLUME knob (3).

• When necessary, operate the CROSSOVER

knob (4

) and PHASE

switch (6), and then adjust with the VOLUME

knob (

3).

4. Turn the POWER switch (2) OFF.

• The power indicator disappears.

1POWER ON

POWER

VOLUME M AX

MIN

AC IN

OFF

200 Hz

50 Hz

CROSSOVER

BYPASS

PHASE

LINE LEVEL

INPUTOUTPUT

Rear Panel

RCA dplug cor

TROUBLESHOOTING

Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong with this component, check the

points below. Sometimes the trouble may lie in another component. and electrical appliances be Investigate the other components ing used. If the

trouble cannot be rectified even after exercising the checks listed below, ask your nearest PIONEER authorized service center or your dealer to carry

out repair work.

SPECIFICATIONS

Cabinet ............................................................Bass-reflex, floor-standing type

Speaker..................................................................................... 30 cm cone type

Power Amplifier Continuous Power Output (RMS)

Taiwan................................................................................150 W/6 Ω(100 Hz)

All other models................................................................200 W/6 Ω(100 Hz)

Input (sensitivity at 100 Hz/impedance)

LINE LEVEL (RCA jack) ..............................................................175 mV/50 kΩ

Output (Level at 100 Hz/impedance)

LINE LEVEL (RCA jack) ................................................................175 mV/1 kΩ

Selectable CROSSOVER Frequencies ..................................... 50 Hz to 200 Hz

Outline Dimension ..........................360 mm (W) x 437 mm (H) x 455 mm (D)

Weight (without package)....................................................................... 15.2 kg

Power Requirements

Taiwan, Mexico, Middle Latin America models

........................................................................... 110 V to 127 V~, 50 Hz/60 Hz

All other models............................................... 220 V to 240 V~, 50 Hz/60 Hz

Power Consumption

Taiwan, Mexico, Middle Latin America models ...................................155 W

All other models......................................................................................184 W

Accessories

Power cable: Taiwan, Mexico, Middle Latin America models ................ x 2

All other models ...................................................................x 1

Operating instructions

Specifications and design subject to possible modification without

notice, due to improvements.

Published by Pioneer Corporation.

SYMPTOM CAUSE REMEDY

1 No power is being supplied

(Indicator does not light up when

power switch is turned on.)

• Power supply plug is not correctly

inserted.

• Insert plug securely.

2 No sound

(Indicator is lit.)

• Connection of RCA plug cord is wrong

or disconnected.

• .VOLUME knob is set to MIN

• Check again and connect correctly.

• Turn clockwise slowly.

3 Sound is distorted. • Level is too high.

• Input level is too high.

• Turn the VOLUME knob counter-clockwise to lower the level.

• Turn the amplifier’s output level (volume, bass control, bass

boost) counter-clockwise to lower the level.

4 Howling noise occurs. • No power supplied to the amplifier.

• Subwoofer level is set too high.

• Connect an amplifier and supply power.

• Place the subwoofer a good distance from speakers. Turn the

VOLUME knob counter-clockwise to lower the volume.

5 Much noise when listening to

AM or FM broadcasts.

• The AM loop antenna or the FM indoor

antenna is close to this unit.

• Increase the distance between the AM or FM antenna (for

indoor use) and this unit.

Operating Instructions

Manual de instrucciones

S-RS3SW

POWERED SUBWOOFER

ALTAVOCES DE GRAVES SECUNDARIOS ENERGIZADOS

The exclamation oint within an equilate al p r

t iangle is intended to ale t the use to the r r r

pr p r p resence of im o tant o e ating and

maintenance (se vicing) inst uctions in the r r

lite atu e accom anying the a liance. r r p pp

The lightning flash with a owhead symbol, rr

within an equilate al t iangle, is intended to r r

ale t the use to the esence of uninsulated r r pr

"dange ous voltage" within the oduct's r pr

enclosu e that may be of sufficient r

magnitude to constitute a isk of elect ic r r

shock to e sons.p r

CAUTION:

TO PREVENT THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER (OR

BACK). NO USER-SERVICEABLE PARTS

INSIDE. REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

IMPORTANT

D3-4-2-1-1_En-A

WARNING

This equipment is not waterproof. To prevent a fire

or shock hazard, do not place any container filled

with liquid near this equipment (such as a vase or

flower pot) or expose it to dripping, splashing, rain

or moisture. D3-4-2-1-3_B_En

WARNING

The voltage of the available power supply differs

according to country or region. Be sure that the

power supply voltage of the area where this unit

will be used meets the required voltage (e.g., 230 V

or 120 V) written on the rear panel. D3-4-2-1-4_A_En

Befo e the fi st time, r plugging in for r read the following

section ca efully.r

WARNING

To prevent a fire hazard, do not place any naked

flame sources (such as a lighted candle) on the

equipment. D3-4-2-1-7a_A_En

VENTILATION CAUTION

When installing this unit, make sure to leave space

around the unit for ventilation to improve heat

radiation (at least 25 cm at top, 15 cm at rear, and

10 cm at each side).

WARNING

Slots and openings in the cabinet are provided for

ventilation to ensure reliable operation of the

product, and to protect it from overheating. To

prevent fire hazard, the openings should never be

blocked or covered with items (such as newspapers,

table-cloths, curtains) or by operating the

equipment on thick carpet or a bed.

D3-4-2-1-7b_A_En

Operating Environment

O e ating envi onment tem e atu e and humidity:p r r p r r

+5 ºC to +35 ºC (+41 ºF to +95 ºF); less than 85 %RH

(cooling vents not blocked)

Do not install this unit in a oo ly ventilated a ea, o in p r r r

locations ex osed to high humidity o di ect sunlight (o p r r r

st ong a tificial light)r r D3-4-2-1-7c_A_En

If the AC lug of this unit does not match the AC p

outlet you want to use, the lug must be emoved p r

and a o iate one fitted. Re lacement and ppr pr p

mounting of an AC lug on the owe su ly co d of p p r pp r

this unit should be e fo med only by qualified p r r

se vice e sonnel. If connected to an AC outlet, the r p r

cut-off lug can cause seve e elect ical shock. Make p r r

su e it is o e ly dis osed of afte emoval.r pr p r p r r

The equi ment should be disconnected by emoving p r

the mains lug f om the wall socket when left p r

unused fo a long e iod of time (fo exam le, when r p r r p

on vacation). D3-4-2-2-1a_A_En

CAUTION

The POWER switch on this unit will not com letely p

shut off all owe f om the AC outlet. Since the p r r

p r r r rowe co d se ves as the main disconnect device fo

the unit, you will need to un lug it f om the AC outlet p r

to shut down all owep r. The efo e, make su e the r r r

unit has been installed so that the owe co d can p r r

be easily un lugged f om the AC outlet in case of an p r

accident. To avoid fi e haza d, the owe cor r p r rd should

also be un lugged f om the AC outlet when left p r

unused fo a long e iod of time (fo exam le, when r p r r p

on vacation). D3-4-2-2-2a_A_En

POWER-CORD CAUTION

Handle the owe co d by the lug. Do not ull out the p r r p p

p r r p rlug by tugging the co d and neve touch the owe

co d when you hands a e wet as this could cause a r r r

sho t ci cuit o elect ic shock. Do not lace the unit, a r r r r p

p r r p r r r piece of fu nitu e, etc., on the owe co d, o inch the

co d. Neve make a knot in the co d o tie it with othe r r r r r

co ds. The owe co ds should be outed such that they r p r r r

a e not likely to be ste ed on. A damaged owe co d r pp p r r

can cause a fi e o give you an electr r rical shock. Check

the owe co d once in a while. When you find it p r r

damaged, ask you nea est PIONEER autho ized r r r

se vice cente o you deale fo a e lacement.r r r r r r r p S002*_En

Thank you for buying this PIONEER product. Please read through these operating instructions so you will know how to operate your model properly. After