Használati útmutató Roland F-30

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Roland F-30 (5 oldal) a nincs kategorizálva kategóriában. Ezt az útmutatót 14 ember találta hasznosnak.

/ 5 PDF

1

DIGITAL PIANODate: Oct 8, 2002

Model:F-30Version 1.00MIDI IMPLEMENTATION

1.Receive Data

■Channel Voice Messages

●Note o

Status2nd byte3rd byte

8nH kkH vvH

9nH kkH 00H

n = MIDI channel number : 0H-FH (ch.1-ch.16)

kk = note number : 00H-7FH (0-127)

vv = note o velocity : 00H-7FH (0-127)

*The velocity values of Note O messages are ignored.

●Note on

Status2nd byte3rd byte

9nH kkH vvH

n = MIDI channel number : 0H-FH (ch.1-ch.16)

kk = note number : 00H-7FH (0-127)

vv = note on velocity : 01H-7FH (1-127)

*Note numbers outside the range of 15-113 are transposed to the nearest octave within

this range.

*Transpose function does not aect the recognized note numbers.

●Control Change

*The value specied by a Control Change message will not be reset even by a Program

Change, etc.

❍Data Entry (Controller number 6, 38)

Status2nd byte3rd byte

BnH 06HmmH

BnH 26HllH

n = MIDI channel number : 0H-FH (ch.1-ch.16)

mm, ll = the value of the parameter specied by RPN

❍Volume (Controller number 7)

Status2nd byte3rd byte

BnH 07HvvH

n = MIDI channel number : 0H-FH (ch.1-ch.16)

vv = Volume : 00H-7FH (0-127), Initial Value = 7FH (127)

*Received volume messages aect received note event levels, and cannot aect internal

keyboard notes.

❍Expression (Controller number 11)

Status2nd byte3rd byte

BnH 0BHvvH

n = MIDI channel number : 0H-FH (ch.1-ch.16)

vv = Expression : 00H-7FH (0-127), Initial Value = 7FH (127)

*These message can aect only MIDI notes.

❍Hold 1 (Controller number 64)

Status2nd byte3rd byte

BnH 40HvvH

n = MIDI channel number : 0H-FH (ch.1-ch.16)

vv = Control value : 00H-7FH (0-127) 0-63 = OFF, 64-127 = ON

*These message can aect only MIDI notes.

❍Sostenuto (Controller number 66)

Status2nd byte3rd byte

BnH 42HvvH

n=MIDI channel number : 0H-FH (ch.1-ch.16)

vv=Control value : 00H-7FH (0-127) 0-63 = OFF 64-127 = ON

*These message can aect only MIDI notes.

❍Soft (Controller number 67)

Status2nd byte3rd byte

BnH 43HvvH

n=MIDI channel number : 0H-FH (ch.1-ch.16)

vv=Control value : 00H-7FH (0-127) 0-63 = OFF 64-127 = ON

*These message can aect only MIDI notes.

❍Eect 1 (Reverb Send Level) (Controller number 91)

Status2nd byte3rd byte

BnH 5BHvvH

n=MIDI channel number : 0H-FH (ch.1-ch.16)

vv=Control value : 00H-7FH (0-127) 0-63 = OFF 64-127 = ON

❍RPN MSB/LSB (Controller number 100, 101)

Status2nd byte3rd byte

BnH 65HmmH

BnH 64HllH

n = MIDI channel number : 0H-FH (ch.1-ch.16)

mm = upper byte of parameter number specied by RPN(MSB)

ll = lower byte of parameter number specied by RPN(LSB)

*The value specied by RPN will not be reset even by messages such as Program Change

or Reset All Controller.

* *RPN**

The RPN (Registered Parameter Number) messages are expanded control changes, and each

function of an RPN is described by the MIDI Standard.

To use these messages, you must rst use RPN MSB and RPN LSB messages to specify the

parameter to be controlled, and then use Data Entry messages to specify the value of the

specied parameter. Once an RPN parameter has been specied, all Data Entry messages

received on that channel will modify the value of that parameter. To prevent accidents, it is

recommended that you set RPN Null (RPN Number = 7FH/7FH) when you have nished

setting the value of the desired parameter.

On the F-30, RPN can be used to modify the following parameters.

RPNData entry

MSB LSBMSB LSBExplanation

00H 01HmmH llHMaster Fine Tuning

mm, ll: 00 00H - 40 00H - 7F 7FH (-100 - 0 - +99.99 cents),

Initial Value = 40 00H (±0 cent)

7FH 7FH--- ---RPN null

Set condition where RPN and NRPN are unspecied.

The data entry messages after set RPN null will be ignored.

(No Data entry messages are required after RPN null).

Settings already made will not change.

mm, ll: ignored

Termékspecifikációk