Használati útmutató Shaws AUSH-4341
Olvassa el alább 📖 a magyar nyelvű használati útmutatót Shaws AUSH-4341 (8 oldal) a Daru kategóriában. Ezt az útmutatót 72 ember találta hasznosnak és 36.5 felhasználó értékelte átlagosan 4.9 csillagra
Oldal 1/8
min
HOT
IN
COLD
IN
Hose Length mm
G 1/2” to suit
double check valve
Con-Serv DCCFF
G 1/2” to suit
double check valve
Con-Serv DCCFF
G 1/2”
G 1/2”
mm
hole
mm
mm
hole
mm max
Yarrow
AUSH.4341 - MONOBLOC MIXER
AUSH.4146 - MONOBLOC MIXER WITH SPRAY RINSE
Please Note: This model does not suit incoming water pressure
below 100kPa or higher than 500kPa. The spray rinse model requires
a minimum inlet pressure of 100kPa to successfully divert the water
flow from the main tap to the spray rinse. The stop cocks provided
with this tap contain gauze filters. Please ensure your plumber is
advised of the minimum and maximum water pressure, and to install
the stop cocks as failure to do so voids the tap warranty.
Temperature Range
Min 1°C. Max 70°C
Working Pressure
Min 100kPa (14.5psi). Max 500kPa (72.5psi)
Flow Rates AUSH.4341
Bar: L/min
Bar: L/min
Bar: L/min
AUSH.4346
Bar: L/min
Bar: L/min
Bar: L/min
Ideal performance obtained with equal hot & cold pressures.
IMPORTERS & DISTRIBUTORS OF FINE KITCHEN AND BATHROOMWARE
6 | French Avenue, Brendale QLD 4500 | aftersales@luxebydesign.com.au | www.luxebydesign.com.au
40mm MAX WORK SURFACE
Dual check valve
Con-Serv
DCCFF
Hose Length
mm
mm
Hole
mm
Hole
COLD
IN
HOT
IN
Non-return valve adaptor
mm max
8
Yarrow | INSTALLATION AND USER GUIDE
1
Ensure the mixer is oriented correctly, the lever should
be on the right when viewed from the front. Hot and
cold hoses are indicated with a red or blue sticker. We
recommend a minimum distance of 70mm from the
wall to the hole centre for the main tap. x mm
hole is required to mount the mixer. If you have a spray
rinse model, an additional mm hole located to the
left or right hand side of the tap is also required for
the spray rinse unit. Maximum counter top thickness is
40mm. Extension kits are available for thicker benchtops.
Insert the flexible connectors through the hole,
ensuring that the base ring and seal are in place
between the mixer and the mounting surface.
From the underside of the counter top, place the
clamp plate on securing stud and using the box spanner
supplied, place the fixing nut in the spanner and tighten
until the mixer is held firmly in position.
If your mixer has a rinse, please follow steps 2, 3 & 4 to
install correctly, otherwise please connect the hot &
cold water supplies.
Ensure all connections are firmly tightened.
3
Ensure the black rubber washers are situated inside position A,
B (either side of) and C on the rinse hose, including the NRV
adaptor in sequence as displayed in the diagram.
Screw the rinse onto the end of the flexible hose from the tap.
Ensure the connection is firmly tightened.
4
Thread the tapered end of the rinse flex hose into the rinse
unit, ensuring the rubber seal is in place between them.
Ensure all connections are firmly tightened.
2
Secure the rinse unit socket in a suitable position using a tap
wrench of a 36 AF spanner.
Place the flexible hose through the top of the rinse unit socket as
shown in the diagram.
LUXEBYDESIGN.COM.AU
DISTRIBUTED IN AUSTRALIA BY LUXE BY DESIGN SERVICE@LUXEBYDESIGNCOMAU
ø30mm
Hole
WORK SURFACE
Base seal
Rinse unit
socket
Fibre washer
Backnut
Flexible hose
WORK SURFACE
A
C
B
Rinse
hose
Dual
check
valve
NRV
adaptor
G 3/8”
Base ring
Base seal
WORK SURFACE
Clamp plate
Fixing nut
Flexible
connections
40mm MAX WORK SURFACE
Double
check valve
Hose Length
mm
mm
Hole
mm
Hole
COLD
IN
HOT
IN
Non-return valve adaptor
Rinse
hose
Rinse unit
socket
Base seal
Rinse
Black rubber
washer
Fibre washer
Backnut
BEFORE USE
Carefully check the installation for leaks
If further building work is being carried out in the vicinity, cover the product to avoid damaging the finish.
Please ensure the installation complies with the water supply by-laws.
Congratulations on the purchase of your Shaws by Perrin & Rowe kitchen product. Correctly installed and with sensible care,
this product will give you many years of trouble-free service.
INSTALLATION REQUIREMENTS
Perrin & Rowe tapware must be installed by a Licensed Plumber in accordance with the installation instructions provided, best
trade practices and must comply to local plumbing regulations in your area. Incorrect installation may damage your tap and
could invalidate your warranty.
Where the inlet water pressure exceeds 500kpa, pressure limiting valves must be installed.
In-line gauze filters must be fitted in the incoming water supply lines.
Prior to installation, it is important to flush all incoming water lines thoroughly. Failure to do so may result in issues caused
by debris in the water supply such as bits of metal or plastic, dirt, sand, rust, silt, and other unwanted materials. Any
problems that arise as a result of inadequate flushing may not be covered by the warranty.
Please take care of this product before, during and after installation as accidental damage to the tap finish is not covered
by the warranty. Please wear gloves when handling 'living finish' models. If further work is to be carried out in the vicinity of
the product, please cover it to protect from paint, plaster, adhesives, sealants and cleaning products.
For ease of possible future servicing, we recommend the fitting of conveniently placed isolating valves.
Once unpacked, remove fixing nuts, clamp plate, fibre washer and plastic backnut from tap assembly, ready for installation.
Yarrow | INSTALLATION AND USER GUIDE
LUXEBYDESIGN.COM.AU
DISTRIBUTED IN AUSTRALIA BY LUXE BY DESIGN SERVICE@LUXEBYDESIGNCOMAU
FINE ADJUSTMENT OF LEVER HANDLE POSITION
Once your plumber has installed your tapware, occasionally you may
find the levers aren't straight or the logo may be slightly crooked. Every
Perrin & Rowe tap handle has a unique white nylon alignment vernier
positioned between the spindle of the ceramic disc valve and the base
of the lever handle hood. This vernier allows fine tuning of the handle
position during or after the initial installation.
To adjust the handle position:
1. Simply remove the handle by unscrewing the hood in an anti-
clockwise direction and pull the handle assembly off.
2. Lift the vernier off the valve spindle or carefully remove it from
inside the handle spline using needle-nose pliers.
3. Rotate the vernier slightly
4. Place the vernier back onto the valve spindle, in its new position
5. Replace the handle and check the alignment. Adjust again if
required until the alignment is straight.
SPRAY RINSE
The additional bench-mounted spray rinse tap features a retractable
1.2m hose and a simple diverter button which can be activated with a
press of your thumb. The water ceases to run through from the main
tap, activating the spray rinse to make filling pots, rinsing vegetables,
watering plants and washing oversized dishes fuss-free and simple. The
spray rinse is an integral component of each tap and cannot be added
later to a non-spray rinse tap model.
CARE AND MAINTENANCE
Perrin & Rowe taps and accessories are made in Britain from premium quality brass. Each piece is hand polished and
electroplated in a range of beautiful finishes. While our finishes exceed industry standards for thickness and quality, they need
appropriate care to maintain the beauty of the product and to preserve your warranty.
Following a simple cleaning routine after use will maintain the beauty of your brassware, and preserve the warranty. Ideally,
fittings should be dried with a soft cloth after each use. Clean regularly by dampening a microfibre cloth with warm water
combined with a mild PH-neutral liquid soap, then polish with a soft, lint-free cloth to finish. Microfibre cloths are ideal as they
are gentle but effective at cleaning brassware without scratching. This approach is suitable for all finishes, except for Gold
which should be dried with a leather chamois cloth.
General Tips for all Finishes
Dry fittings after use with a soft cloth.
Residue left from personal hygiene products such as soap or cleaning gels can cause blemishes on your brassware.
Completely rinse off all fittings with clean water, and dry after use.
Avoid getting bleach or harsh chemicals and cleaners on your taps when cleaning surrounding surfaces. Covering your
fixtures with a cloth or towel reduces the risk of damaging your brassware finishes.
To remove limescale, use a 50/50 solution of lemon juice and water. Soak cotton wool in the solution and leave wrapped
around the tap for no longer than hour, then rinse clean with water and fully dry with a lint-free cloth. For heavy scaling, the
process can be repeated provided the area is rinsed with clean water between treatments to avoid a build-up of citric acid.
Avoiding Damage
Under no circumstances should harsh cleaning agents containing acidic, caustic or abrasive components such as bleach,
alcohol or vinegar-based substances be used.
Do not use abrasive cloths, scouring pads, scrub sponges, steel wool etc. as they may damage the surface.
To avoid dye and patterning transfer from wet cloths, avoid hanging them over the spout of the tap. Porous surfaces such
as nickel, pewter and unlacquered brass finishes may be affected by chemicals in or on the cloth.
Damage caused through the actions described above would not be covered by Perrin & Rowe's warranty.
WATERMARK
Perrin & Rowe manufactures kitchen taps especially for the Australian market using DZR
(dezincification resistant) brass of the highest quality, with fittings which are compatible with
Australian plumbing standards. WaterMark certification (license number WMKA02818) has been
awarded to the Perrin & Rowe tapware which is made for Australia. Perrin & Rowe tapware sold
elsewhere in the world is not certified for Australia, contains different brass and plumbing fittings
and cannot be legally installed.
WELS RATING
Perrin & Rowe kitchen tapware has been tested and certified with
WELS under the Water Efficiency Labelling & Standards (WELS)
scheme with License number 1938.
Shaws by Perrin & Rowe Kitchen Taps have been awarded a WELS
L/min Four Star rating
Shaws by Perrin & Rowe Spray Rinse Taps have been awarded a
WELS L/min Six Star rating for the spray tap and WELS L/min Five
Star rating for the mixer tap
Hood
Vernier
Ceramic
disc valve
Faceplate
Mesh filter
Quad seal
Retaining ring
Non-return valve
O-ring
Spindle
Button
retaining
ring
Termékspecifikációk
| Márka: | Shaws |
| Kategória: | Daru |
| Modell: | AUSH-4341 |
Szüksége van segítségre?
Ha segítségre van szüksége Shaws AUSH-4341, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek
Útmutatók Daru Shaws
8 Április 2025
8 Április 2025
8 Április 2025
8 Április 2025
8 Április 2025
Útmutatók Daru
- Daru Teka
- Daru Smeg
- Daru Livarno
- Daru Quooker
- Daru Sloan
- Daru Nodor
- Daru Peerless-AV
- Daru Miomare
- Daru Neo
- Daru Puretec
- Daru Stiebel Eltron
- Daru Moen
- Daru Zurn
- Daru Zip
- Daru Hansgrohe
Legújabb útmutatók Daru
8 Április 2025
8 Április 2025
8 Április 2025
8 Április 2025
8 Április 2025
8 Április 2025
8 Április 2025
8 Április 2025
7 Április 2025
7 Április 2025