Használati útmutató Sonance Visual Performance VP65 SST

Sonance hangszóró Visual Performance VP65 SST

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Sonance Visual Performance VP65 SST (8 oldal) a hangszóró kategóriában. Ezt az útmutatót 11 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/8
1
Introduction
Thank you for purchasing Sonance Visual Performance ®
Single-Stereo Technology®(SST) or surround (SUR) speakers.
When properly installed your new speakers will give you years
of entertainment pleasure.
Box Contents
I
I
I
IIt
t
t
tte
e
e
eem
m
m
mm Quantity (SST)
Quantity (SST)
Quantity (SST)
Quantity (SST)Quantity (SST) Quantity (SUR)
Quantity (SUR)
Quantity (SUR)
Quantity (SUR)Quantity (SUR)
Visual Performance Speaker 1 2
Paintable Grille 1 2
Plastic Paint Plug 1 2
Mounting Cutout Template 1 1
Speaker Placement
SST Models
Because a single SST speaker reproduces both stereo channels
from a single location, it will deliver outstanding performance
from a wide variety of mounting locations where a pair of stereo
speakers would be impractical, including hallways, bathrooms
and closets.
The table below shows how far apart SST speakers can be
spaced in distributed audio applications while still providing
good coverage for standing and seated listeners (see
Figure 1
).
Ceiling Height
Ceiling Height
Ceiling Height
Ceiling HeightCeiling Height S
S
S
SSpacing (Standing)
pacing (Standing)
pacing (Standing)
pacing (Standing)pacing (Standing) Spacing (Seated)
Spacing (Seated)
Spacing (Seated)
Spacing (Seated)Spacing (Seated)
9-Foot Ceiling 5’7” (1.7m) 9’5” (2.9m)
10-Foot Ceiling 9’7” (3.0m) 13’5” (4.1m)
12-Foot Ceiling 13’7” (4.2m) 17’5” (5.3m)
14-Foot Ceiling 17.7’ (5.4m) 21’5” (6.6m)
SUR Models:
5.1-Channel Home Theater System
Mount the left and right surround speakers on the ceiling 2 – 6
feet (0.6m – 1.8m) behind the listening position. The speakers
should be 6 – 10 feet (1.8m – 3m) apart. Orient the speakers so
the tweeters face the front and rear walls of the room. Use
Figure
2
as a guide.
SUR Models:
7.1-Channel Home Theater System
Mount the left and right surround speakers directly to the sides of
the listening position, 6 – 10 feet (1.8m – 3m) apart. Mount the
surround back speakers 2 – 6 feet (0.6m – 1.8m) behind the
listening position. The surround back speakers should be closer
together than the left and right surround speakers, 3 – 6 feet
(0.9m – 1.8m) apart. Use
Figure 3
as a guide.
TV
3' – 6'
(0.9m – 1.8m)
apart
2' – 6'
(0.6m – 1.8m)
Surround
Back
Speaker
Surround
Back
Speaker
Right Surround
Speaker
Left Surround
Speaker
F P 7.1-C SIGURE 3: SUR SPEAKER LACEMENT IN A HANNEL YSTEM
I N S T R U C T I O N M A N U A L
V I S U A L P E R F O R M A N C E ® S E R I E S
S S T A N D S U R S P E A K E R S
TV
6' – 10'
(1.8m – 3m)
apart
2' – 6'
(0.6m – 1.8m)
Right Surround
Speaker
Left Surround
Speaker
F P 5.1-C SIGURE 2: SUR SPEAKER LACEMENT IN A HANNEL YSTEM
C
OVERAGE
A
REA
C
OVERAGE
A
REA
S
PEAKER
S
PACING
F A S SIGURE 1: DISTRIBUTED UDIO PEAKER PACING
S W :AFETY ARNING
THESE SPEAKERS HAVE AST OUNTF M ® TABS THAT PREVENT THE
SPEAKER FROM FALLING OUT OF THE MOUNTING HOLE DURING T HE
INSTALLAT ION PROCESS.
T F MHE EDGES OF THE AST OUNT TABS ARE VERY SHARP.
U SE CAUTION WHEN HANDLING TH E SPEAKER.
2
SONANCE VISUAL PERFORMANCE®SST & SUR
Before Installation: Retrofit
1. Determine the location for the speaker (see
Speaker
Placement
, on page 1).
2. Perform an obstruction survey to be certain that there are no
studs, conduit, pipes, heating ducts, pocket doors or air returns
in the wall or ceiling cavity that will interfere with the speaker.
3. Mounting space require ments:
Mounting space requi rements:
Mounting space requi rements:
Mounting space requi rements:Mounting space requi rements:
• Larg e round SST & SU R:
Larg e rou nd SST & SU R:
Larg e rou nd SST & SU R:
Larg e rou nd SST & SU R:Larg e rou nd SST & SU R: 10 1⁄8" (257mm) diameter
cut-out; 5 7⁄8" (149mm) depth within the mounting cavity.
• Large square SST :
Large squa re SST:
Large squa re SST:
Large squa re SST:Large squa re SST: 10¼" x 10¼" (260mm x 260mm)
cut-out; 5 7⁄8" (149mm) depth within the mounting cavity.
• Medium round SST & SUR:
Medium round SST & SUR:
Medium round SST & SUR:
Medium round SST & SUR:Medium round SST & SUR: 8¼" (210mm) diameter
cut-out; 4¾" (121mm) depth within the mountinig cavity.
• Medium square SST :
Med ium square SST :
Med ium square SST :
Med ium square SST :Medi um square SST: 8¼" x 8¼" (210mm x 210mm)
cut-out; 4¾" (121mm) depth within the mounting cavity.
• Medium rectangle SST:
Medium rectangle SST:
Medium rectangle SST:
Medium rectangle SST: Medium rectangle SST: 6 15⁄16" x 10¾" (176mm x 273mm)
cut-out; 3 9⁄16" (91mm) depth within the mounting cavity.
• Medium T hinLin e round SST :
Med ium T hinLine round SST :
Med ium T hinLine round SST :
Med ium T hinLine round SST :Med ium T hinLine round SST : 8¼" (210mm) diameter
cut-out; 3 1⁄
32 " (77mm) depth within the mounting cavity.
• Sm a ll r oun d SST :
Sm a ll r ou n d SST :
Sm a ll r ou n d SST :
Sm a ll r ou n d SST :Sm a ll r ou n d SST : 5 7⁄8" (149mm) diameter cut-out;
3½" (89mm) depth within the mounting cavity.
• 5
Small square SST :
Small square SST :
Small square SST :
Small square SST :Small square SST : 5⁄8" x 5 5⁄8" (143mm x 143mm)
cut-out; 3 5⁄8" (92mm) depth within the mounting cavity.
4. Position the included cut-out template where the speaker is to
be located and pencil an outline on the wall or ceiling. If you
are unsure about obstructions, drill a small hole in the center
of the outline and insert a coat hanger wire into the hole to
feel-around for possible obstructions.
5. Cut the mounting hole using a keyhole or drywall saw, and
run the speaker wires from the mounting hole to the amplifier
location.
NOTE : CONSULT LOCAL BUILDING CODES BEFOR E RUNNING
SPEAKER WIRES THR OUGH CEILINGS.
Installation
Visual Performance SST SUR speakers feature exclusiveAND
FastMount tabs and an integral Roto-Lock®mounting system for
quick mounting directly into existing walls and ceilings.
WARNING: The edges of FastMount tabs are very
sharp. Use caution when handling the speaker.
1. Remove the paint plug from the speaker.
2. Run speaker wire from each speaker to the amplifier location.
3. Strip ¼” – ½” (6mm – 12mm) of insulation from each speak-
er lead. Twist the strands or tin the exposed wire with solder
to ensure that there are no stray strands. (Stray strands that
touch each other can cause a short-circuit that can damage
the amplifier.)
4. The speaker’s connector posts are spring-loaded. Push the top
of each connector post down to open the connector and insert
the exposed wires into the holes in the posts.
• The speaker’s positive post is labeled with a red dot; the neg-
ative post is labeled with a black dot. Double-check that you
connected amplifier “+” to speaker “+” and amplifier “–” to
speaker “–”.
5. Make sure all the Roto-
Lock clamps are in the
full clockwise position
so that they are tucked
within the mounting
hole’s border. Insert the
speaker into the hole in
the wall or ceiling
(
Figure 4
). The Roto-
Lock system can accom-
modate a maximum
wall or ceiling material
thickness of 1¼”
(32mm).
The FastMount tabs
will prevent the speak-
er from falling out of
the mounting hole,
allowing the installer
to let go of the speaker
to pick-up tools or
other items (
Figure 5
).
N FOTE: THE AST OUNTM
TABS ARE DESIGNED FOR
ONE TIME USE ONLY- .
IF THE SPEAKER IS
REMOVED FROM THE
MOUNTING HOLE THE
FAST OUNT TABS WILLM
DISCONNECT AND
REMAIN INSIDE THE WALL
OR CEILING.
6. Tighten the four screws on the front of the speaker baffle
(
Figure 6
). The Roto-Lock clamps will automatically rotate into
position and begin clamping the speaker. When you notice resist-
ance on the screws the speaker has been clamped successfully.
IMPORTANT: Always use low-torque settings;
NEVER over-tighten.
Roto-Lock Clamps
(retracted)
F S IIGURE 4: INSERT PEAKER NTO
M HOUNTING OLE
Roto-Lock
Screws
Roto-Lock
Screws
F R -LIGURE 6: TIGHTENING THE OTO OCK CREWSS
FastMount Tabs
FIGURE 5: FAST OUNTM TABS
3
SONANCE VISUAL PERFORMANCE®SST & SUR
N OTE OTO: ADJUSTING THE TENSION OF THE R -LOCK CLAMPS
SO THAT THE SPEAKER FRAME IS FLAT WILL HELP ENSURE THAT THE
GR ILLE CONTACTS THE WALL ALL THE WAY AROU ND THE SPEAKER
FOR A PROPER FIT.
7. The new micro-trim grille is held in place by several small,
powerful magnets on the speaker frame. Place the grille
against the speaker and the magnets will hold it firmly in
place. When properly installed, the grille trim should make
contact with the wall all the way around the speaker.
Painting The Speakers and Grilles
Please refer to the included
Painting Instructions
sheet.
Speaker Adjustments
Pivoting Woofer
Some SST and SUR models have a pivoting woofer assembly. This
allows you to direct sound toward or away from the listening
area, depending on how the speakers are being used:
• For SST models, pivoting the woofer towards the listening
position will maximize the speaker’s clarity and definition.
• For SUR models, you can create a more diffuse, spacious
surround effect by aiming the woofers towards a wall or
window, away from the listeners.
N POTE: WHE N IVOTING THE W O O F E R S IN MODE LSUR
SPEAKERS MAKE SURE THAT THE TWEETERS REMAIN OR IENTED,
TOWARDS THE FRONT AND REAR WALLS FOR SIDE SURROUND
SPEAKERS AND TOWARDS THE SID E WALLS FOR SUR, ROUND BACK
SPEAKERS.
To pivot the woofer,
apply pressure on the
outer edge of the
tweeter support brack-
et, as shown in
Figure
7
. Do not touch or
apply pressure to the
woofer cone.
F 7:IGURE
P IVOTING THE OOFERW

Termékspecifikációk

Márka: Sonance
Kategória: hangszóró
Modell: Visual Performance VP65 SST

Szüksége van segítségre?

Ha segítségre van szüksége Sonance Visual Performance VP65 SST, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók hangszóró Sonance

Sonance

Sonance Visual Performance VP38R Útmutató

9 Január 2025
Sonance

Sonance MAG5.1R Útmutató

9 Január 2025
Sonance

Sonance MAG6R Útmutató

9 Január 2025
Sonance

Sonance Visual Performance Extreme VPXT8R Útmutató

8 Január 2025
Sonance

Sonance Mariner MX52 Útmutató

2 Január 2025
Sonance

Sonance Visual Performance VP65 SST Útmutató

16 Október 2024
Sonance

Sonance Landscape LS6T SAT Útmutató

7 Október 2024
Sonance

Sonance Visual Performance VP87 Útmutató

6 Október 2024
Sonance

Sonance Mariner MX66 Útmutató

11 Szeptember 2024
Sonance

Sonance MAG06V3 Útmutató

2 Szeptember 2024

Útmutatók hangszóró

Legújabb útmutatók hangszóró

Behringer

Behringer B2520 PRO Útmutató

10 Április 2025
Marshall

Marshall Willen Útmutató

10 Április 2025
JBL

JBL Control 426LP Útmutató

9 Április 2025
Crestron

Crestron SAROS IC8T Útmutató

8 Április 2025
LD Systems

LD Systems STINGER G3 TMB Útmutató

8 Április 2025
JBL

JBL Conceal C83 Útmutató

8 Április 2025
Crestron

Crestron SAROS ICE4T Útmutató

7 Április 2025
Crestron

Crestron SAROS ICI6T Útmutató

7 Április 2025
Focal

Focal K2 Power M FRAK Útmutató

5 Április 2025
Match

Match UP C42BMW-FRT.3 Útmutató

3 Április 2025