Használati útmutató Speco Technologies AES4
Oldalak 1 Engels hangszóró
Olvassa el ingyen online a(z) Speco Technologies AES4 használati útmutatóját, vagy töltse le PDF-ben. Az útmutatót 17 ember találta hasznosnak. Kérdése van a modellről? Tegyen fel kérdést
A
AE
ES
S4
4
4” Amplified Extension Speaker
Thank you for your choice of Speco Technologies’ Amplified Speaker. This unit is designed and manufactured AES4
to provide an economical solution to the traditional amplifier and speaker setup. The sturdy ABS construction and
power up to 18W max ensure a long and versatile life.
DESCRIPTION
The utilizes an integrated circuit (IC) for providing the necessary gain to raise a low audio input signal AES4
(approximately 1/8 Watts) to at least 10 Watts output. 16 Watts of audio can be obtained with less than 10%
distortion. A DC voltage source supplying 10 to 16 Volts at 1.5 Amperes is required to provide the proper power to
the unit. The unit’s power leads have an in-line fuse holder containing a 2 Ampere fuse for short circuit or
overload protection. In addition, the unit has built-in protection against reverse polarity of the power leads.
INSTALLATION INSTRUCTIONS:
1)The is constructed with an indexing, metal mounting bracket. AES4
2)Loosen the knobs connecting the metal bracket to the speaker and remove.
3)The bracket contains an opening to secure to the mounting surface with screws (included). It is advised to
secure the bracket before connecting the speaker.
4)Reconnect the bracket to the speaker, tilt the speaker to the desired angle, and tighten the knobs to lock
the speaker at the desired angle.
5)The DC power leads should be connected to a switched power source since the unit draws up to 200
milliamperes, even when no audio signal is present.
6)The 3.5mm jack should then be connected to your desired audio source.
7)Volume is set and controlled from the source.
SPECIFICATIONS:
•Input Impedance: 3-16 Ohms
•Input Audio Level: 1.5 VPP, Max.
•Audio Output Power: 18 W Max., 10 W RMS
•Audio Output Distortion: 10% or less at 16W output
•Speaker Impedance: 4 Ohms
•Supply Voltage Range: 10-16V DC
•Current Draw: @13.8V DC
oStandby (No Audio Input): 200MA, Max.
o16 W Output: 1.5A, Max
•Fuse: 2 Amp
Speco Technologies is constantly developing and improving products.
We reserve the right to modify product design and specifications without notice and without incurring any obligation.
Speco Technologies . 200 New Highway . Amityville . NY . 11701 . www.specotech.com
Rev. 04/08/20
Termékspecifikációk
| Márka: | Speco Technologies |
| Kategória: | hangszóró |
| Modell: | AES4 |
Szüksége van segítségre?
Ha segítségre van szüksége Speco Technologies AES4, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek
Útmutatók hangszóró Speco Technologies
Speco Technologies SPG86T Útmutató Speco Technologies SPCE5OB Útmutató Speco Technologies SP6NXCTUL Útmutató Speco Technologies SP5MATB Útmutató Speco Technologies SPCE6OTW Útmutató Speco Technologies SPRK65CBT Útmutató Speco Technologies DMS3TS Útmutató Speco Technologies SRD100 Útmutató
Összes Speco Technologies hangszóró használati útmutató
Népszerű termékek – hangszóró
Speco Technologies SP6MAT Útmutató Speco Technologies SPC12RP Útmutató Speco Technologies SPC15R Útmutató