Használati útmutató Velleman ET20

Velleman Fűtő ET20

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Velleman ET20 (12 oldal) a Fűtő kategóriában. Ezt az útmutatót 7 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/12
ET20
ETCHING TANK WITH AGITATOR AND HEATER
ETSTANK MET VERWARMINGSELEMENT EN POMP
GRAVEUSE VERTICALE AVEC POMPE ET RÉSISTANCE
GRABADOR CON BOMBA Y ELEMENTO CALENTADOR
ÄTZMASCHINE MIT PUMPE UND HEIZUNG
USER MANUAL 2
GEBRUIKERSHANDLEIDING 4
MODE D'EMPLOI 5
MANUAL DEL USUAR 7IO
BEDIENUNGSANLEITUNG 9
ET20
V. 03 17/02/2016 2 ©Velleman nv –
USER MANUAL
1. Introduction
To all residents of the European Union
Important environmental information about this product
This symbol on the device or the package indicates that disposal of the device after its lifecycle could
harm the environment. Do not dispose of the unit (or batteries) as unsorted municipal waste; it
should be taken to a specialized company for recycling. This device should be returned to your
distributor or to a local recycling service. Respect the local environmental rules.
If in doubt, contact your local waste disposal authorities.
Thank you for choosing Velleman! Please read the manual thoroughly before bringing this device into service. If
the device was damaged in transit, don't install or use it and contact your dealer.
Check first if you have all the pieces: the air pump and its tube, the heater with thermostat and the [1] [5]
tank, consisting of the tank itself , 2 tank support pieces , and 3 fixation clips and wires . Refer [3] [2] [7] [6]
to the illustration on page 2 of this manual.
2. Safety Instructions
Keep this device away from children and unauthorized users.
WARNING: this tank must be filled with an etching solution (not included), e.g.
ammonium persulfate, hydrochloric acid or ferric chloride. These products are toxic and
(highly) corrosive. Do not inhale vapours. Avoid eye or skin contact at all times.
Dispose of etching liquid in accordance with local regulations. pour etching liquid Never
into the sewers.
3. General Guidelines
Refer to the on the last pages of this manual. Velleman® Service and Quality Warranty
Indoor use only. Keep this device away from rain, moisture, splashing and dripping liquids.
Never put objects filled with liquids on top of or close to the device.
ET20
V. 03 17/02/2016 3 ©Velleman nv –
Keep this device away from dust and extreme temperatures.
Protect this device from shocks and abuse. Avoid brute force when operating the device.
Familiarise yourself with the functions of the device before actually using it.
All modifications of the device are forbidden for safety reasons. Damage caused by user modifications to
the device is not covered by the warranty.
Only use the device for its intended purpose. Using the device in an unauthorised way will void the warranty.
Damage caused by disregard of certain guidelines in this manual is not covered by the warranty and the
dealer will not accept responsibility for any ensuing defects or problems.
Keep this manual for future reference.
4. Assembly
Refer to the illustrations on page 2 of this manual.
1. First, fill the tank [3] with water and check for leaks. If no leaks are found, remove the water from the tank.
2. One of the air inlets on the tank is sealed.
Connect the air pump to the free air inlet by means of the plastic tube. [1]
3. Fit the heater (spare part order code ET200) at the side opposite the air inlet. The heater is pre-[5]
regulated and set for a temperature of approx. °C, the optimal temperature for ferric chloride treatment. 32
4. Carefully tighten the clamping screw.
5. Install the support pieces [2] in the tank’s grooves.
The etching tank is now ready to be used.
Safety Warning
You should only remove the heater in exceptional circumstances, as it is not without danger. The glass of the
heater may crack under the influence of the difference in temperature when the warm heater comes into
contact with cold water. There is a genuine risk of electroshocks if this happens. Therefore, you should always
unplug the device and let the heater cool down before removing it. You should also make sure that your hands
are dry when you are connecting or disconnecting the device. Take care to use this device with the suitable
amount of etching solution.
5. Operation
1. Place the air pump higher than the liquid level in the tank to avoid flow-back. [1]
2. Fill the tank with the desired solution: use 2.25 L to fill the tank. : The red line on the heater Caution [4]
must always be covered liquid. in
3. Turn the heater on and let it heat up for 2 minutes.
4. Put the plastic clips on the printed board, and adjust the length of the fixation wires . Put the board [7] [6]
in the tank at ± 1 cm below the liquid surface.
5. Turn the air pump on to agitate the liquid. [1]
6. Monitor the evolution of the etching. You can place a lamp behind the tank; because the tank is
transparent, you can see what happens. At the correct temperature, etching takes about 4 minutes.
7. When finished, wash away any trace of the product under running water.
8. Finally, inspect the tracks of your etched circuit.
6. Technical Specifications
etching tank with pump and heater
300 W / 230 Vac
spare heater (not incl.)
order code ET200
dimensions
external
360 x 280 x 40 mm
internal
350 x 230 x 30 mm
tank capacity
2 L .5
Use this device with original accessories only. Velleman nv cannot be held responsible in the event
of damage or injury resulting from (incorrect) use of this device. For more info concerning this
product and the latest version of this manual, please visit our website www.velleman.eu. The
information in this manual is subject to change without prior notice.
© COPYRIGHT NOTICE
The copyright to this manual is owned by Velleman nv. All worldwide rights reserved. No part of this
manual may be copied, reproduced, translated or reduced to any electronic medium or otherwise without the
prior written consent of the copyright holder.

Termékspecifikációk

Márka: Velleman
Kategória: Fűtő
Modell: ET20

Szüksége van segítségre?

Ha segítségre van szüksége Velleman ET20, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók Fűtő Velleman

Velleman

Velleman CH0005 Útmutató

24 Szeptember 2024
Velleman

Velleman ET20 Útmutató

2 Szeptember 2024
Velleman

Velleman CH0006 Útmutató

29 Augusztus 2024

Útmutatók Fűtő

Legújabb útmutatók Fűtő

Dimplex

Dimplex VFMi 60C Útmutató

6 Április 2025
Scandia

Scandia Styliste’ 6 Útmutató

4 Április 2025
Einhell

Einhell MR 7 S Útmutató

30 Március 2025
Argoclima

Argoclima Dori Night Útmutató

30 Március 2025
Dimplex

Dimplex 2NC81524L Útmutató

30 Március 2025
Dimplex

Dimplex FXL24i Útmutató

30 Március 2025
DeLonghi

DeLonghi RHJ21F1015 Útmutató

27 Március 2025
Rinnai

Rinnai GEPH-22DTW Útmutató

27 Március 2025
Einhell

Einhell NKH 1500 Útmutató

27 Március 2025
Einhell

Einhell NBH 2000 H Útmutató

27 Március 2025