Használati útmutató Velleman K8023

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Velleman K8023 (20 oldal) a távirányító kategóriában. Ezt az útmutatót 11 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Oldal 1/20
10 Channel, 2-Wire REMOTE CONTROL
K8023
H8023IP-1
Control up to 10 devices from a
distance using only 2 wires.
2
Features:
Microprocessor controlled.
Inputs can be push-buttons, switches or open collector outputs from another device.
The receiver section provide 10 open collector outputs which allow you to control relays directly.
Terminal block connectors for all input and output connections are included.
All outputs are provided with LED indication.
Can be used with our kits: K8000,K8006,K8046,K8050,…
Can be connected to our standard relay card: K6714, K6714-16
Specifications:
10 open collector outputs 50V/100mA
Tested to a distance of up to 50m (55 yards) between control- and receiver section.
Operating voltage: Single 12-15V AC or DC, 300mA.
Dimensions control pcb (wxdxh): 70x50x16mm (2,7”x2”x0,6”).
Dimensions receiver pcb (wxdxh): 103x50x24mm(4”x2”x1”).
Features & Specifications
3
Assembly hints
1. Assembly (Skipping this can lead to troubles ! )
Ok, so we have your attention. These hints will help you to make this project successful. Read them carefully.
1.1 Make sure you have the right tools:
A good quality soldering iron (25-40W) with a small tip.
Wipe it often on a wet sponge or cloth, to keep it clean; then apply solder to the tip, to give it a wet look. This is calledthinning’ and will
protect the tip, and enables you to make good connections. When solder rolls off the tip, it needs cleaning.
Thin raisin-core solder. Do not use any flux or grease.
A diagonal cutter to trim excess wires. To avoid injury when cutting excess leads, hold the lead so they
cannot fly towards the eyes.
Needle nose pliers, for bending leads, or to hold components in place.
Small blade and Phillips screwdrivers. A basic range is fine.
For some projects, a basic multi-meter is required, or might be handy
1.2 Assembly Hints :
Make sure the skill level matches your experience, to avoid disappointments.
Follow the instructions carefully. Read and understand the entire step before you perform each operation.
Perform the assembly in the correct order as stated in this manual
Position all parts on the PCB (Printed Circuit Board) as shown on the drawings.
Values on the circuit diagram are subject to changes.
Values in this assembly guide are correct*
Use the check-boxes to mark your progress.
Please read the included information on safety and customer service
* Typographical inaccuracies excluded. Always look for possible last minute manual updates, indicated as ‘NOTE’ on a separate leaflet.

Termékspecifikációk

Márka: Velleman
Kategória: távirányító
Modell: K8023

Szüksége van segítségre?

Ha segítségre van szüksége Velleman K8023, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek




Útmutatók távirányító Velleman

Velleman

Velleman DVRRC4 Útmutató

9 December 2024
Velleman

Velleman MK160 Útmutató

4 Augusztus 2024
Velleman

Velleman LEDC06 Útmutató

3 Augusztus 2024
Velleman

Velleman VM161 Útmutató

2 Augusztus 2024
Velleman

Velleman VM118R Útmutató

2 Augusztus 2024
Velleman

Velleman VM201 Útmutató

29 Július 2024
Velleman

Velleman VM151 Útmutató

17 Július 2024
Velleman

Velleman K8023 Útmutató

13 Július 2024
Velleman

Velleman IREXT Útmutató

5 Július 2024
Velleman

Velleman VM130 Útmutató

19 Május 2024

Útmutatók távirányító

Legújabb útmutatók távirányító