Használati útmutató Velleman K8200

Velleman 3D nyomtató K8200

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Velleman K8200 (16 oldal) a 3D nyomtató kategóriában. Ezt az útmutatót 8 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/16
English
.....................................................................
2
Nederlands
.............................................................
5
Français
...................................................................
8
Deutsch
...................................................................
11
Espanõl
....................................................................
14
- 2 -
VELLEMAN-KIT
3D Printer kit
Order code: K8200
manufactured by:
VELLEMAN NV.
Legen Heirweg, 33
9890 Gavere
Belgium
CE conformity information:
The K8200 is a DIY 3D printer kit, it contains all the bits and pieces to construct your own 3D printer but does not contain
additional protection.
As it is a kit and not a nished product, compliance with the CE regulations depends on the build-quality; also the following
notes must be taken into account.
Conductive EMC towards the public distribution network is not an issue as this is related to the power supply.
Radiated EMC depends substantially on the build quality, it might be required to add shielding but this cannot be predicted.
A built K8200 should comply with EN50081 normation
Electromagnetic radiation (EMC):
The included power supply meets all the applicable European requirements and bears the CE-mark.
It is protected against overload and short circuit and nothing needs to be modied. The working voltage of the 3D printer is
15Vdc (extra low voltage) and therefore it’s outside the scope of the Low voltage directive.
Always unplug before maintenance or modication.
Electrical safety:
!
Important safety instructions
The 3D printer contains a lot of moving parts, but the force of the stepper motors is too low to cause serious injuries. Never-
theless it is recommended to provide additional protection against mechanical risks.
The easiest way to make your 3D printer “accident proof” is to put it inside a protective enclosure which completely covers
the 3D printer – with or without an access door and fume extraction. (numerous designs can be found on the internet)
To make it extra safe a switch which interrupts the power supply of the printer when the enclosure or door is opened can be
added. It is also advisable to install an external emergency stop switch, which also cuts off the power supply.
Providing adequate protection is the responsibility of the assembler.
Always cut power before maintenance or modication.
Mechanical safety and protection:
!
The 3D printer is not intended for use by persons (including children) with reduced physical, or mental capabilities,
or lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of
the appliance by a person responsible for their safety
Children should be supervised to ensure that they do not play with the appliance.
The above information is believed to be correct but does not purport to be all inclusive and shall be used only as a guide.
The information in this document was obtained from sources which we believe are reliable.
However, the information is provided without any warranty, express or implied, regarding its correctness.
The conditions or methods used for assembling, handing, storage, use or disposal of the device are beyond our control and
may be beyond our knowledge. For this and other reasons, we do not assume responsibility and expressly disclaim liability
for loss, injuries, damage, or expense arising out of or in any way connected with the assembly, handling, storage, use or
disposal of the product.
General safety information:
There is a potential risk of burns as the Printer head (extruder) can reach up to 270°C.
The use of common sense should be sufcient to prevent burns, but in some environments it is highly recommended to
provide additional protection. (see § Mechanical safety and protection)
The max. temperature of the heated bed is 60°C, this is below the 1 min. burn threshold for plastic surfaces according to
CENELEC Guide 29. Normal reexes prevent long contact periods with hot surfaces
Always let the 3D printer cool down for 60 min. before maintenance or modication.
Risk of burns:
!
This printer is designed for use with PLA and ABS lament (MSDS for the Velleman lament is available).
PLA: is a safe and non-toxic material, there are no known health safety risks when used in 3D printers.
ABS: when printing with ABS there is a distinctive ‘burned plastic’ smell. This is quite normal but it may also cause head-
aches, respiratory- and eye irritation with sensitive people (although it is not toxic)
Only use the printer in a well-ventilated area, if printing with ABS it is advisable to add a fume hood (with active car-
bon ltering for ductless extraction). Fume extraction is mandatory for use in ofces, classrooms and alike.
Never burn printer lament, toxic gasses and vapors will be generated if exposed to re.
Health:
!
- 3 -

Termékspecifikációk

Márka: Velleman
Kategória: 3D nyomtató
Modell: K8200

Szüksége van segítségre?

Ha segítségre van szüksége Velleman K8200, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók 3D nyomtató Velleman

Velleman

Velleman K8400 Útmutató

14 Július 2024
Velleman

Velleman K8200 Útmutató

10 Július 2024

Útmutatók 3D nyomtató

Legújabb útmutatók 3D nyomtató

Creality3D

Creality3D Printmill Útmutató

31 December 2025
Creality

Creality CR-10 Smart Pro Útmutató

27 December 2024
Creality

Creality Ender-3 V2 Neo Útmutató

27 December 2024
Creality

Creality Halot-Lite Útmutató

27 December 2024
Creality

Creality Ender-3 S1 Pro Útmutató

27 December 2024
Raise3D

Raise3D E2CF Útmutató

12 December 2024
Flashforge

Flashforge Hunter Útmutató

27 Szeptember 2024
Flashforge

Flashforge Creator 3D Útmutató

14 Szeptember 2024
Wasp

Wasp Delta 2040 Clay Útmutató

3 Szeptember 2024
Wasp

Wasp Delta 20 40 Turbo Útmutató

3 Szeptember 2024