Használati útmutató Vivotek AW-IHT-0601

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Vivotek AW-IHT-0601 (2 oldal) a nincs kategorizálva kategóriában. Ezt az útmutatót 8 ember találta hasznosnak és 5 felhasználó értékelte átlagosan 4.3 csillagra

1. Install the switch in a ventilated and dry place that is free of electromagnetic source, vibration, moisture, and dust.

2. Make sure the ventilation openings on the switch are not blocked.

3. Use ber optic cables and transceiver compliant with the following: Multi-mode: 50/125um, 62.5/125um, 850nm;

Single-mode): 9/125um ,1310nm.

4. DC input: (AW-IHT-0600 - 44V~56VDC; AW-IHT-0601 - 12~56VDC). Follow the printed polarity for V+, V-, and Ground.

AW-IHT-0600 Industrial PoE Switch

AW-IHT-0601

Quick Installation Guide

The AW-IHT-0600 series is a rugged media PoE switch designed for delivering a max. of 30 watts to powered devices.

The optional TX or FX uplink port can be used to extend the connection to a remote site. With its multi-purpose design, it

is t for IP surveillance, trafc monitoring, and security applications in critical environments. The machine features a total

budget of 126 watts and a wide range of operating temperatures ranging from -40°C to 75°C.

IMPORTANT:

INTRODUCTION

CONNECTION

* 1x PoE switch* 1x Quick Installation Guide* 1x 6-pin terminal block

* 2x wall mount brackets* 1x DIN rail bracket

PACKAGE CONTENTS

1. Pull out the 6-pin terminal block.

2. Connect positive wires to V+, negative wires to V-, and

neutral wire to the ground screw.

Connect the 24V DC @1A pins to external devices.

When 2 power pins are connected, the relay is shorted.

When any of them is diconnected, the relay connection

is open.

3. Connect SFP transceivers and ber cables to the ber

ports.

4. Install the 6-pin terminal block.

1 2

ON

F5 1000M

T5 100M

DIP 1F5Enable the F5 ber port (default)

T5Enable the T5 Ethernet port

DIP 21000MThe F5/T5/F6 port in the Gigabit mode (default)

100MThe F5/F6 ber port in the 100Mbit mode. If T5 (Ethernet) is put to use, the

T5 port can not operate in the 100Mb mode.

WARNING - Always ground the power source to maintain a clean power input.

- OR -

LAN/WAN

T5

F5

PW1 ONWhen power is connected.

PW2 ONWhen power is connected.

ERR (relay)OFFWhen both PW1 and PW2 are

connected.

ONOnly PW1 or PW2 is connected.

F5 ONPort 5 ber is detected.

OFFPort 5 ber is not detected.

Flashing Data is being transmitted or received.

F6 ONPort 6 ber is detected.

OFFPort 6 ber is not detected.

Flashing Data is being transmitted or received.

Link ONTX link is detected.

OFF Link is not detected.

FlashingPort is active.

SPD ON1000M speed is detected.

OFF10/100M speed is detected.

P1,P2,P3,

P4

ONPD is detected on the designated port.

OFFNo PD is detected.

LED DEFINITIONS

IMPORTANT - You can either use the F5 ber or the T5 Ethernet port. These ports can not be

used at the same time. Use the DIP switch to make the selection.

Note that the conguration change only takes effect after a power cycle.

Termékspecifikációk