Használati útmutató Whirlpool ADG 5010 IX

Whirlpool mosogatógép ADG 5010 IX

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Whirlpool ADG 5010 IX (8 oldal) a mosogatógép kategóriában. Ezt az útmutatót 6 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF

Oldal 1/8

EN -1-

-1-

-1--1-

Chart

PROGRAMS SE

PROGRAMS SEPROGRAMS SELECTION

LECTION

LECTION LECTION

BUTTON

BUTTONBUTTON

Push “P” button (repeatedly)

until selected program number

is shown on the display

(P1...Px) - see “Table of

programs” below.

STSTART/RESUME BUTTON

ART/RESUME BUTTON

ART/RESUME BUTTONART/RESUME BUTTON

Push this button to start the selected program: the

indicator lights up and goes off at the end of the

program.

When the door is opened during a washing cycle,

the cycle is temporarily paused: the Start indicator

blinks. To resume the cycle close the door and

push Start button again.

CANCEL/OFF BU

CANCEL/OFF BUCANCEL/OFF BUTTON

TTON

TTONTTON

Push this button to switch off the control panel.

If pressed when a program is running it cancels the

program ongoing draining water for 1 minute

(0:01 is shown into the display).

If pressed when the dishwasher is switched off,

it drains any possible liquids from dishwasher

(1 minute process).

(see at right for

(see at right for (see at right for options description)

options description)

options description)options description)

1)1) Program dat

Program dat

Program datProgram data obtained in confor

a obtained in confor

a obtained in confora obtained in conformity with European sta

mity with European sta

mity with European stamity with European standard EN 50242, obtaine

ndard EN 50242, obtaine

ndard EN 50242, obtainendard EN 50242, obtained under normal condit

d under normal condit

d under normal conditd under normal conditions (without any options)

ions (without any options)

ions (without any options)ions (without any options) a

a and may vary d

nd may vary d

nd may vary dnd may vary depending on

epending on

epending on epending on

conditions. Di

conditions. Diconditions. Differences of up to 2

fferences of up to 2

fferences of up to 2fferences of up to 20 minutes are possi

0 minutes are possi

0 minutes are possi0 minutes are possible with sensor progra

ble with sensor progra

ble with sensor prograble with sensor programs as a result of the a

ms as a result of the a

ms as a result of the ams as a result of the appliance’s automat

ppliance’s automat

ppliance’s automatppliance’s automatic calibrat

ic calibrat

ic calibratic calibration system.

ion system.

ion system.ion system.

2)2) Refer

Refer

ReferReference progra

ence progra

ence prograence program for energy lab

m for energy lab

m for energy labm for energy label in compl

el in compl

el in complel in compliance with EN

iance with EN

iance with ENiance with EN 50242 regula

50242 regula

50242 regula 50242 regulations. - Not

tions. - Not

tions. - Nottions. - Note for T

e for T

e for Te for T

esting Inst

esting Instesting Institutes: for

itutes: for

itutes: foritutes: for detailed i

detailed i

detailed i detailed infor

nfor

nfornforma

mamation on

tion on

tion ontion on the

the

the the

EN/Standard loading c

EN/Standard loading cEN/Standard loading comparison test and other

omparison test and other

omparison test and otheromparison test and other tests, contact the

tests, contact the

tests, contact the tests, contact the following address: “cont

following address: “cont

following address: “cont following address: “contact@whirlpool.com”.

act@whirlpool.com”.

act@whirlpool.com”.act@whirlpool.com”.

*Power consumption in Left-

*Power consumption in Left-*Power consumption in Left-on mode: 1

on mode: 1

on mode: 1on mode: 1.27 W / Off-mode:

.27 W / Off-mode:

.27 W / Off-mode: .27 W / Off-mode: 0.40 W

0.40 W

0.40 W0.40 W.

able of pr

able of prable of programs

ograms

ogramsograms

Deter-

Deter-Deter-

gent

gentgent

Consumpt

ConsumptConsumption

ion

ionion

Drying

DryingDrying

Phase

PhasePhase

Programs

ProgramsPrograms Available

Available

AvailableAvailable

options

optionsoptions Loading instruction

Loading instruction

Loading instructionLoading instructions

Litres

LitresLitres kWh

kWh

kWhkWh Minutes

Minutes

MinutesMinutes1)

1)1)

P1P1

Sensor

SensorSensor 40°-70°C

40°-70°C

40°-70°C40°-70°C

Delay

1/2 load

PowerClean®

Recommended program for routine

washes, with dried-on food. X 7-15 70-1721.00-1.70 Full

P2P2

Pre

PrePre-W

-W

-W-Wa

aash

shsh cold

cold

coldcold Delay Crockery to be washed later. — 4.0 0.01 14-16 NO

P3P3

Rapi

RapiRapid

dd 45°C

45°C

45°C45°C Delay Lightly soiled crockery, with no

dried-on food. X 11.0 0.85 30-50 NO

P4P4 Eco

Eco

EcoEco 2)

2)2) 50°C

50°C

50°C50°C

Delay

1/2 load

PowerClean®

Normally soiled crockery.

Standard program, the most efficient

in terms of its combined energy and

water consumption.

X 10.0 0.92 240 Full

P5P5

Daily

DailyDaily 60°C

60°C

60°C60°C Delay

1/2 load Normally to heavily soiled crockery. X 11.0 1.30 80-95 Full

P6P6 Steam

Steam

SteamSteam Delay

PowerClean®

Program including steam action

dedicated for heavily soiled crockery,

pots and pans.

Soaking or hand pretreatment is no

longer needed.

X 14.5 1.75 180-190 Full

5019 300 02456

5019 300 024565019 300 02456

BEFORE USING THE APPLIANCE FOR THE

BEFORE USING THE APPLIANCE FOR THE BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULL

FIRST TIME CAREFULL

FIRST TIME CAREFULLFIRST TIME CAREFULLY READ THIS

Y READ THIS

Y READ THIS Y READ THIS

QUICK REFERENCE GUIDE AND THE ASSEMBL

QUICK REFERENCE GUIDE AND THE ASSEMBLQUICK REFERENCE GUIDE AND THE ASSEMBLY INSTRUCTIONS!

Y INSTRUCTIONS!

Y INSTRUCTIONS!Y INSTRUCTIONS!

Options and display description

SAL

SALSALT INDICA

T INDICA

T INDICAT INDICATOR

TOR

TORTOR

When lit (at the end of the cycle),

the salt reservoir needs to be

refilled.

RINSE AID INDICATOR

RINSE AID INDICATORRINSE AID INDICATOR

When lit (at the end of the cycle),

the rinse aid dispenser needs to

be refilled.

THE CONTROL P

THE CONTROL PTHE CONTROL PANEL OF

ANEL OF

ANEL OF ANEL OF THIS DISHW

THIS DISHW

THIS DISHWTHIS DISHWASHER ACTIV

ASHER ACTIV

ASHER ACTIVASHER ACTIVA

AATES PUSHING ANY

TES PUSHING ANY

TES PUSHING ANY TES PUSHING ANY

BUTTON EXC

BUTTON EXCBUTTON EXCEPT CANCEL/OFF BUTTON.

EPT CANCEL/OFF BUTTON.

EPT CANCEL/OFF BUTTON.EPT CANCEL/OFF BUTTON.

FOR ENERGY SA

FOR ENERGY SAFOR ENERGY SAVING THE CONTROL P

VING THE CONTROL P

VING THE CONTROL PVING THE CONTROL PANEL DEACTIV

ANEL DEACTIV

ANEL DEACTIVANEL DEACTIVA

AATES

TES

TES TES

AUTOMA

AUTOMAAUTOMATICALL

TICALL

TICALLTICALLY AFTER 30 SECONDS IF NO CYCLE HAS ST

Y AFTER 30 SECONDS IF NO CYCLE HAS ST

Y AFTER 30 SECONDS IF NO CYCLE HAS STY AFTER 30 SECONDS IF NO CYCLE HAS STARTED.

ARTED.

ARTED.ARTED.

1/2 L

1/2 L1/2 LOAD BUTTO

OAD BUTTO

OAD BUTTOOAD BUTTON

Half load cycle can be used

for the upper or lower

rack.

Select the required

program then press the

“Half Load” button - the

light comes on.

Turns off at the end of the

program.

The “Half Load” option

can be used with the

programs indicated in the

table of programs.

TTABLET SETTING

ABLET SETTING

ABLET SETTINGABLET SETTING

This setting allows to optimize

the cycle performances

according the type of detergent

used.

Push the Tablet button for

3 seconds (until the indicator

lights up) if you are using the

combined detergents in tablet

(rinse aid, salt and detergent in

1 dose). If you are using powder

detergent or gel detergent, the

Tablet indicator on the control

panel has to be off.

DELA

DELADELAYED ST

YED ST

YED STYED START BUTTON

ART BUTTON

ART BUTTONART BUTTON

Push the button

(repeatedly) to delay the

start of the program –

delay indicator turns on.

Adjustable from 1 to

24 hours. With each press

of the button, the delay

increases by one hour and

after “h 24” returns to

“h 00”. When this option

is selected the delay

indicator turns on. Then

press the START button.

The dishwasher will start

after the set time.

POWERCLEAN

POWERCLEANPOWERCLEAN®

®®

Thanks to the additional power jets this option provides a more

intensive and powerful wash in the lower rack, in the specific area.

This option is recommended for washing pots and casseroles

(see page 4). Press this button to activate PowerClean

(the indicator lights up).

WASH TIME DISPLAY

WASH TIME DISPLAYWASH TIME DISPLAY

Indicated the cycle

duration and the

remaining time (h:min).

With “Delayed start”

selected it indicates the

time remaining until

program start (h.00) -

below 1h (0:min).

If “Fx Ey” messages

appears on the display,

see page 6 - chapter

“What to do if...”.

Quick reference guide

Quick reference guideQuick reference guide

Whirlpool is a registered trademark of Whirlpool USA

Whirlpool is a registered trademark of Whirlpool USAWhirlpool is a registered trademark of Whirlpool USA

EN -2-

-2-

-2--2-

First time use

5 7 86

1- salt reservoir

2- rinse aid dispenser

3- detergent dispenser

4- racks system

5,6,7,8- available functions on the panel

9- filters

10- spray arms

WWater hardness should be set before the

ater hardness should be set before the

ater hardness should be set before the ater hardness should be set before the

first wash or if water hardness has been

first wash or if water hardness has been first wash or if water hardness has been

changed.

changed.changed.

(depending on the model)

The salt level indicator lamp may remain lit at

the end of several wash cycles. If the water

hardness set to level 1 (soft), no salt is required

and salt indicator lamp will remain off.

Salt indicator on the control panel

Salt indicator on the control panelSalt indicator on the control panel Salt indicator on the salt reservoir cap

Salt indicator on the salt reservoir cap

Salt indicator on the salt reservoir capSalt indicator on the salt reservoir cap

The indicator lamp lights up when SALT

NEEDS TO BE ADDED. green: OK. clear: NEEDS TO

BE ADDED

- Press and hold together PROGRAM Selection

PROGRAM Selection

PROGRAM SelectionPROGRAM Selection and CANCEL/Off

CANCEL/Off

CANCEL/OffCANCEL/Off buttons for minimum 3 seconds.

- The current water hardness setting will be visible on the display.

- Press the PROGRAM Selection

PROGRAM Selection

PROGRAM SelectionPROGRAM Selection button to increase setting. Value range goes from 1 to 7 (when the level reaches 7, the next

press of the start button will set the level back to 1).

- Wait 30 seconds (control panel switches off) or press Start/Resume

Start/Resume

Start/ResumeStart/Resume button to save setting.

1Visual indicator

(depending

on the model).

Unscrew cap.

Fill the salt reservoir with water

before the first wash only.

Daily check

Filling the salt reservoir -

Filling the salt reservoir - Filling the salt reservoir - Dissolve limescale (not necessary if water hardness level is set to “soft”!)

Add salt

Add salt Add salt (never add detergent!)

min. 0.8 kg / max. 1 kg

Screw on the cap.

Salt residual

around the cap

need to be

removed. Some

salt reservoir have

a level indicator

integrated in the

cap (see below

how to check).

Once regeneration salt is added, immediate

immediate

immediateimmediately

lyly start a wash program (the “Pre-wash” program alone is not

not

notnot sufficient).

Residual saline solution or grains of salt can lead to deep-down corrosion, irreparably damaging the stainless steel components.

The guarantee is not applicable if faults are caused by such circumstances.

1.1. Ask your water supply company what the water hardnes

water hardnes

water hardneswater hardness

ss is... 2.

2.2. ...enter this value on

your dishwasher SALT

required

German

degrees °dH

French

degrees °fH

English

degrees °eH

Water hardness

level

Insert value is shown

in the display

0 - 5 0 - 9 0 - 6.3 Soft 1 NO

6 - 10 7 - 12.610 - 18 Medium 2

YES

11 - 15 19 - 27 13.3 - 18.9 Average 3

16 - 21 28 - 37 19.6 - 25.9 Medium-hard 4

22 - 28 38 - 50 26.6 - 35 Hard 5

29 - 35 51 - 63 35.7 - 44.1 Very hard 6

36 - 50 64 - 90 44.8 - 62.4 Extremely hard 7

Water hardness level is

factory set for medium-

hard water (level 4).

Detergents

When you use Powder or

Gel you must use salt and

set up water hardness level

as indicated in the table on

the right.

Also when you use

Tablets which include salt

functionality you must still

add regeneration salt.

How to set water hardness in order to always assure the best cleaning results

How to set water hardness in order to always assure the best cleaning resultsHow to set water hardness in order to always assure the best cleaning results

Before first use, run the appliance

Before first use, run the appliance Before first use, run the appliance with detergent and without loading.

with detergent and without loading.

with detergent and without loading.with detergent and without loading.

EN -3-

-3-

-3--3-

Daily check

Check the rinse aid indicator to check the level

into the dispenser.

(depending on the model)

Rinse aid indicator on the control panel

Rinse aid indicator on the control panelRinse aid indicator on the control panel Rinse aid indicator on th

Rinse aid indicator on th

Rinse aid indicator on thRinse aid indicator on the dispenser

e dispenser

e dispensere dispenser

The indicator lamp lights up when RINSE AID NEEDS

TO BE ADDED. dark: OK. clear: NEEDS TO BE ADDED.

Only use rinse aids recommended for use in domestic dishwashers. Immedia

Immedia

ImmediaImmediately

tely

telytely wipe away any rinse aid spilt accidentally. This prevents the formation of excess suds which can cause a fault function of the

appliance.

If there are streaks: reduce the dosage by turning the dial to a lower setting (1-3). If crockery is not perfectly dry: increase the dosage by turning the dial to a higher setting (5-6). Plastic dishes have more difficulty

drying and a higher rinse aid setting will not improve the situation.

Detergents with rinse aid incorporated may be effective only with longer programs. In the case of shorter programs, detergent residue may be a problem (if necessary, use powder detergent). Detergents with

rinse aid incorporated tend to form excess suds.

Daily use

Adding detergent -

Adding detergent - Adding detergent - Use only detergent specifically for dishwashers in accordance with the supplier’s recommendations

Open the cover A

(press the dedicated button).

Only fill the

detergent dispenser

prior to starting a

wash program.

Shut the cover

by pressing dedicated ribs.