Használati útmutató Audio-Technica ATM650
Oldalak 2 Engels mikrofon
Olvassa el ingyen online a(z) Audio-Technica ATM650 használati útmutatóját, vagy töltse le PDF-ben. Az útmutatót 18 ember találta hasznosnak. Kérdése van a modellről? Tegyen fel kérdést
HYPERCARDIOID DYNAMIC INSTRUMENT MICROPHONE
- Tailored response for musical instrument pickup-guitar cabinets,
snare and other percussion.
- Hypercardioid polar pattern reduces pickup of sounds from the
sides and rear, improving isolation of desired sound source.
- Durable performance for professional applications.
- Special dual-wall oating construction reduces handling noise and
assures consistent performance from mic to mic.
- Hi-ENERGY® neodymium magnet for improved output and transient
response.
- Multi-stage at grille design is engineered to enable easy placement
as close as possible to sound source.
- Corrosion-resistant contacts from gold-plated XLRM-type connector.
- Rugged, all-metal design and construction for years of trouble-free
use.
Output from the microphone’s XLRM-type connector is low imped-
ance (Lo-Z) balanced. The signal appears across Pins 2 and 3; Pin
1 is ground (shield). Output phase is “Pin 2 hot” - positive acoustic
pressure produces positive voltage at Pin 2.
To avoid phase cancellation and poor sound, all mic cables must be
wired consistently: Pin 1-to-Pin 1, etc. For a high-impedance (Hi-Z)
mic input, connect a Lo-Z balanced cable to a Hi-Z matching trans-
former (A-T CP8201 or equal) at the equipment input.
When using the ATM650 in settings with a stage monitor speaker,
the speaker should be located 135° off axis (45° off rear of the micro-
phone). This placement, in conjunction with the microphone’s uniform
hypercardioid pickup pattern, will virtually eliminate the possibility of
undesired audio feedback.
Take care to keep foreign particles from entering the windscreen. An
accumulation of iron or steel lings on the diaphragm, and/or foreign
material in the windscreen’s mesh surface, can degrade perfor-
mance.
Note: Remove the rubber sleeve at the base of the microphone han-
dle to use the AT8471 isolation stand clamp (not included) for more
secure, permanent installation.
FORM No. ATGC-L0027-06-E
Machida • Tokyo • Japan
10 dB
20k10k5k2k1k50020010050
8 kHz
200 Hz
1 kHz
5 kHz
0°
330°
300°
270°
240°
210°
180°
150°
120°
90°
60°
30°
Polar Pattern
Frequency Response
SCALE IS 5 DECIBELS PER DIVISION
LEGEND
Frequency in Hertz
LEGEND 12” or more on axis
Response in dB
SPECIFICATIONS
ELEMENT Dynamic
POLAR PATTERNHypercardioid
FREQUENCY RESPONSE80-17,000 Hz
OPEN CIRCUIT SENSITIVITY-56 dB (1.5 mV) re 1V at 1 Pa
IMPEDANCE300 ohms
WEIGHT (less cable and accessories)279 g
DIMENSIONS164.2 mm - long,
38.8 mm - diameter
OUTPUT CONNECTORIntegral 3-pin XLRM-type
ACCESSORIES FURNISHEDAT8470 Quiet-Flex™ stand clamp for
⅝”-27 threaded stand;
⅝”-27 to ⅜”-16 threaded adapter;
Soft protective pouch
Termékspecifikációk
| Márka: | Audio-Technica |
| Kategória: | mikrofon |
| Modell: | ATM650 |
Szüksége van segítségre?
Ha segítségre van szüksége Audio-Technica ATM650, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek
Útmutatók mikrofon Audio-Technica
Audio-Technica ES947WC/XLR Útmutató Audio-Technica ATM250DE Útmutató Audio-Technica BP893x Útmutató Audio-Technica MT838IIa Útmutató Audio-Technica AT4060A Útmutató Audio-Technica ES933/ML Útmutató Audio-Technica BP4025 Útmutató Audio-Technica AT2010 Útmutató
Összes Audio-Technica mikrofon használati útmutató
Népszerű termékek – mikrofon
Audio-Technica AT882TH/DS3RC5 Útmutató Audio-Technica ATM-650 Útmutató Audio-Technica ATM610a Útmutató