Használati útmutató Audio-Technica ATM710

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Audio-Technica ATM710 (2 oldal) a mikrofon kategóriában. Ezt az útmutatót 12 ember találta hasznosnak és 6.5 felhasználó értékelte átlagosan 4.3 csillagra

Oldal 1/2
CARDIOID CONDENSER VOCAL MICROPHONE
- Tailored for exacting detail, high-delity vocal reproduction with maxi-
mum impact and intelligibility.
- Excels in venues with controlled stage volume or in-ear monitoring.
- Cardioid polar pattern reduces pickup of sounds from the sides and rear,
improving isolation of desired sound source.
- Durable performance for professional applications.
- Superior anti-shock engineering for low handling noise.
- Multi-stage grille design offers excellent protection against plosives and
sibilance without compromising high-frequency clarity.
- Condenser design for studio-quality performance.
- Integral 80Hz HPF switch and 10 dB pad.
- Corrosion-resistant contacts from gold-plated XLRM-type connector.
- Rugged, all-metal design and construction for years of trouble-free use.
The ATM710 is intended for use in professional applications where remote
power is available. It required 11V to 52V DC phantom power, which may
be provided by a mixer or console, or by a separate, in-line source such
as the Audio-Technica AT8801 single-channel or AT8506 four-channel
phantom power supplies.
Output from the microphone’s XLRM-type connector is low impedance
(Lo-Z) balanced. The signal appears across Pins 2 and 3; Pin 1 is ground
(shield). Output phase is “Pin 2 hot” - positive acoustic pressure produces
positive voltage at Pin 2.
To avoid phase cancellation and poor sound, all mic cables must be wired
consistently: Pin 1-to-Pin 1, etc.
When using the ATM710 in settings with a stage monitor speaker, the
speaker should be located 180° off axis (at rear of the microphone). This
placement, in conjunction with the microphones uniform cardioid pickup
pattern, will virtually eliminate the possibility of undesired audio feedback.
An integral 80Hz hi-pass filter provides easy switching from a flat fre-
quency response to a low-end roll-off. The roll-off position reduces the
microphone’s sensitivity to popping in close vocal use. It also reduces the
pickup of low-frequency ambient noise (such as trafc, air-handling sys-
tems, etc.), room reverberation and mechanically coupled vibrations.
The ATM710 is also equipped with a switchable 10 dB pad that lowers the
microphones’s sensitivity, thus providing higher SPL capability for exible
use with a wide range of performers and system congurations.
Avoid leaving the microphone in the open sun or in areas where tempera-
tures exceed 40°C for extended periods. Extremely high humidity should
also be avoided.
FORM No. ATGC-L0026-06-E
Machida Tokyo Japan
SPECIFICATIONS
ELEMENT Fixed-change back plate permanently
polarized condenser
POLAR PATTERN Cardioid
FREQUENCY RESPONSE 40-20,000 Hz
LOW FREQUENCY ROLL-OFF 80 Hz, 12 dB/octave
OPEN CIRCUIT SENSITIVITY -40 dB (10.0 mV) re 1V at 1 Pa
IMPEDANCE 200 ohms
MAXIMUM INPUT SOUND LEVEL 148 dB SPL, 1 kHz at 1% T.H.D.
DYNAMIC RANGE (typical) 127 dB, 1 kHz at Max SPL
SIGNAL-TO-NOISE RATIO 73 dB, 1 kHz at 1 Pa
PHANTOM POWER REQUIREMENTS 11-52V DC, 3.5 mA typical
SWITCHES Flat, roll-off; 10 dB pad
WEIGHT 274 g
DIMENSIONS 179.0 mm - long,
50.0 mm - diameter
OUTPUT CONNECTOR Integral 3-pin XLRM-type
ACCESSORIES FURNISHED AT8470 Quiet-Flex™ stand clamp for
⅝”-27 threaded stand;
⅝”-27 to ⅜”-16 threaded adapter;
Soft protective pouch
10 dB
20k10k5k2k1k50020010050
8 kHz
200 Hz
1 kHz
5 kHz
330°
300°
270°
240°
210°
180°
150°
120°
90°
60°
30°
Polar Pattern
Frequency Response
SCALE IS 5 DECIBELS PER DIVISION
LEGEND
Frequency in Hertz
LEGEND 12” or more on axis
Response in dB
Roll-off

Termékspecifikációk

Márka: Audio-Technica
Kategória: mikrofon
Modell: ATM710

Szüksége van segítségre?

Ha segítségre van szüksége Audio-Technica ATM710, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek