Használati útmutató Cotech DT8800IP44-5M

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Cotech DT8800IP44-5M (5 oldal) a nincs kategorizálva kategóriában. Ezt az útmutatót 17 ember találta hasznosnak.

GREAT BRITAIN • CUSTOMER SERVICEtel. 020 8247 9300 e-mail customerservice@clasohlson.co.uk internet www.clasohlson.co.uk

postal 10 – 13 Market Place, Kingston Upon Thames, Surrey, KT1 1JZ

1 23

4

5

Ver. 20170920

Flexible RGB LED Strip

Art.no 36-6703 Model DT8800IP44-5M

Please read theentire instruction manual before using theproduct

and then save it for future reference. We reserve theright for

any errors in text or images and any necessary changes made

to technicaldata. In theevent of technical problems or other

queries, please contact our Customer Services.

Safety

• Theproduct should only be connected to a230 V AC,

50Hz electrical outlet.

• Never immerse theproduct in water or other liquid.

• Do not place theproduct where there is arisk of it falling

into water or other types of liquid.

• Theproduct may only be used with thesupplied mains adaptor.

• Theproduct must not be changed or modified in anyway.

• Never hang anything on theproduct.

• Do not look directly into thelight source as there is arisk

for eye damage.

• Never attempt to interconnect theproduct with other light strips.

• Make sure that thepower adaptor is not pinched or

damaged in any other way duringuse.

• Never use theproduct if it, its power adaptor or plug are

damaged in anyway.

• Never let children play with theproduct.

Operating instructions

3. Connect theLED strip to thepower adaptor according to

thefigure (thearrow in thepicture shows theIR receiver for

theremote control).

3. [ ON/OFF ] Power switch

4. [ R, G, B, W ] Solid colour selections

5. [ FLASH ], [ STROBE ], [ FADE ], [ SMOOTH ] Light modes with

7 colours which transition quickly, slowly, smoothly,etc.

Care and maintenance

• Unplug thepower adaptor from thewall socket before

wiping it clean with adrycloth.

• If thepower adaptor is not to be used for anextended

period, it should be unplugged and stored in adry location

out of reach of children.

Changing theremote control batteries

1. Follow theillustration on theback of theremote control.

2. Press in thebattery compartment’s latch and slide it to

release and pull thebattery holder from thecompartment.

3. Insert anew battery into thebattery holder. Makesure that

thepositive (+) terminal is facing upwards, towardsyou.

4. Reinsert thebattery holder back into theremote control.

Responsible disposal

This symbol indicates that this product should not

be disposed of with general householdwaste.

Thisapplies throughout theentire EU. Inorder to

prevent any harm to theenvironment or health

hazards caused by incorrect waste disposal,

theproduct must be handed in for recycling so

that thematerial can be disposed of in aresponsible manner.

Whenrecycling your product, take it to your local collection

facility or contact theplace of purchase. Theywill ensure that

theproduct is disposed of in anenvironmentally sound manner.

Specifications

Note: Withtheexception of theremote control, theproduct

itself has anIP44 rating.

• LED strip with RGB controller, designed to be powered

from a12 V DC, max 1.8 Apower source.

• Theincluded power adaptor delivers 12 V DC, max 2 A, 24 W.

• Bulb: 150LEDs with a460–620 nm wavelengthrange.

• Size: length 5 m, width 12.5 mm, height 4mm. Acertain

amount of deviation in size can be present due to

theglue’s elasticity and thesilicone housing.

• Remote control battery 1×CR2025, 3 V.

1. Thelight strip can be

cut to adesired length.

Note:Cutonly where

marked as shown in

thefigure.

2. Use theincluded adhesive

to glue theprotective

cover over theopen

end of thelightstrip.

Lettheadhesive cure for

at least 12 hours before

subjecting it toload.

4. Hang up thestrip with theincluded cableclips. Becareful

not to damage thecable or mounting surface during

hanging.

5. Plug themains adaptor into anelectrical outlet.

Remote control

Pull theplastic film tab away from thebattery compartment in

order to activate thebattery.

1. Press repeatedly to increase

thebrightness of solid

colours. Increase thespeed

of colour transitions in

thefollowingmodes:

FLASH, STROBE, FADE and

SMOOTH.

2. Press repeatedly to decrease

thebrightness of solid

colours. Decrease thespeed

of colour transitions in

thefollowingmodes:

FLASH, STROBE, FADE and

SMOOTH.

Termékspecifikációk