Használati útmutató Cotech J5218D
Cotech
nincs kategorizálva
J5218D
Olvassa el alább 📖 a magyar nyelvű használati útmutatót Cotech J5218D (6 oldal) a nincs kategorizálva kategóriában. Ezt az útmutatót 14 ember találta hasznosnak és 7.5 felhasználó értékelte átlagosan 4.4 csillagra
Oldal 1/6
GREAT BRITAIN • CUSTOMER SERVICE contact number: 0845 300 9799 e-mail: customerservice@clasohlson.co.uk internet: www.clasohlson.com/uk
6 7 8 9
1 2 3 4 5
Ver. 20140428
Ceiling Light
Art.no 36-4833 Model J5218D
36-4834 J5236D
36-4835 J5258D
Please read theentire instruction manual before using theproduct
and save it for future reference. Wereserve theright for any errors
in text or images and any necessary changes made to technical
data. Ifyou have any questions regarding technical problems
please contact our Customer Services.
1. Safety
• This light fitting is only suitable for permanent installation and
should be installed by aqualified electrician.
• Keep your proper footing and balance at alltimes.
• Make sure that there are no hidden cables or water pipes in
theceiling before drilling holes.
• Read all theinstructions before you install and use thelightfitting.
• Always turn off thepower before installing, wiring or repairing
thelight fitting.
• The light fitting must not be used without thediffuser inplace.
• Warning: Whenever installing any electrical fittings, basic
safety precautions should always be observed to avoid therisk
of fire, electric shock and personal injury.
• Ifyou drill holes in thefitting it will affect Note:
theIPclassification of thefitting.
2. Product description
• Ceiling light (IP65). Suitable for industrial use and in facilities
with high levels of dust, dirt and contaminants.
• Ideal for garages, machine rooms and stables.
• Clear UV-proof polycarbonate diffuser.
• CE-, D- and S-marked.
• For T8 fluorescent tubes (sold separately).
• The light fitting has abuilt-in electronic ballast for aflicker-free
and energy-efficient operation.
• No glow starters are required.
3. Parts
4. Preparations
• Remove theinstallation components from inside thelight
fitting’s chassis.
• Gather all thetools necessary to perform theinstallation.
• Select anappropriate location for thelight fitting.
• Think about theorder in which theparts need to be fitted.
• Purchase thecorrect type of fluorescent tubes.
See section.Specifications
1. Turnthelocking knob (4) to release thechassis plate (3).
2. Liftthechassis plate and take out theinstallation components.
3. Unhookthespring clips (2) from thechassis plate.
4. Readythechassis plate: Pushthefluorescent tube holders (1)
through thechassis plate, make sure they are secured. 8. Maintenance
• Always turn off thepower before carrying out any maintenance.
• You may only replace thefluorescent tube yourself – any other
repairs should be carried out by aqualified electrician.
• Only use fluorescent tubes that match thespecifications.
• Repairs must only be carried out by qualified personnel using
original spareparts.
Replacing the fluorescent tube
Note: Bearin mind that thetube is fragile and should be handled
withcare.
1. Turnoff theelectricity.
2. Waituntil thefluorescent tube has cooled.
3. Removethediffuser by opening thesnaplocks.
4. Turnthefluorescent tube a¼ turn so it can pass through
theslot in theholder, remove thefluorescent tube.
5. Fitthenewtube.
6. Refitthediffuser. Thelight fitting must not be used without
thediffuser inplace.
9. Disposal
This product should be disposed of in accordance with local
regulations. If you are unsure how to proceed, contact your
localauthority.
10. Specifications
36-4833
Model J5218D
Power supply 230 V AC, 50Hz
Fluorescent tube T8, socket G13, 2×18W
Dimensions 660×125×86mm
Weight 0.77kg
Protection class IP65
Number of snap locks 6
36-4834
Model J5236D
Power supply 230 V AC, 50Hz
Fluorescent tube T8, socket G13, 2×36W
Dimensions 1260×125×86mm
Weight 2.12kg
Protection class IP65
Number of snap locks 8
36-4835
Model J5258D
Power supply 230 V AC, 50Hz
Fluorescent tube T8, socket G13, 2×58W
Dimensions 1560×125×86mm
Weight 2.45kg
Protection class IP65
Number of snap locks 10
The product conforms to relevant safety standards and is CE-,
D- and S-marked.
1. Fluorescent tube holder
2. Springclip
3. Chassis plate
4. Chassis plate locking knob
5. Diffuser
6. Snaplock
7. Hanging bracket
8. Cablegland
9. Screwsand wallplugs
5. Assembly
1. Fitthesnap locks (6) to themounts on thecasing.
2. Fitthecable gland (8) into thecasing with thethin rubber
washer on theoutside and anut on theinside. Tighten
thecable gland so that it does not spin when you tighten
theouter seal after thecable has been fitted.
3. Thinkabout how you are going to fix thefitting to theceiling.
There are two alternatives: Hangit from theceiling on awire/
chain attached to thehanging brackets (6) or hang it directly
to theceiling on thehanging brackets.
Alternative 1
Secure awire or chain to theceiling and to thehanging
brackets and then adjust thelength of thewire/chain until
thelight fitting is at thedesired height.
Alternative 2
a) Start by measuring where theholes are to be drilled.
b) Screw thehanging brackets to theceiling using
theincluded screws and wallplugs.
c) Check that everything is ready before you push thelight
fitting into thehanging brackets.
5. Pressthelight fitting up into thehanging brackets.
6. Electrical connections
Note: Thelight fitting has anelectronic ballast and therefore needs
no glow starters.
1. Turnthepower off before beginning any wiring.
2. Themains cable should have aminimum cross-sectional area
of 1.5 mm². Thecircuit must be protected by a10 Afuse.
3. Makesure that thecable gland is fitted properly so that no
water can enter through thehole.
4. Passthemains cable through thecable gland. Makesure
thatthere is at least 17.5 cm of cable inside thecasing of
thelight fitting.
5. Connect thewires to thecorrect terminals (L, earth and N).
Theearth must always be connected.
6. Tighten thesealing nut on thecable gland. Trypulling
thecable gently to make sure that it is held firmly by thegland
and that theseal istight.
7. Reattach thespring clips to thechassis plate and hold
thechassis plate against thelight fitting. Lockthechassis
plate in place by turning thelocking knob.
8. ).Insertthefluorescent tubes (see Replacing thefluorescent tube
9. Carefully fit thediffuser and lock it in place using all
thesnaplocks.
7. Cleaning
1. Turn off thepower and wait until thelight fitting has cooled.
Removethediffuser by opening thesnaplocks.
2. Clean using asoft cloth. Ifnecessary, moisten slightly with
water and mild detergent. Never use alcohol, solvent or similar
agents to clean thelight.
3. Refit thediffuser.
Termékspecifikációk
| Márka: | Cotech |
| Kategória: | nincs kategorizálva |
| Modell: | J5218D |
Szüksége van segítségre?
Ha segítségre van szüksége Cotech J5218D, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek
Útmutatók nincs kategorizálva Cotech
18 Szeptember 2024
15 Szeptember 2024
12 Szeptember 2024
1 Szeptember 2024
28 Augusztus 2024
25 Augusztus 2024
25 Augusztus 2024
25 Augusztus 2024
25 Augusztus 2024
25 Augusztus 2024
Útmutatók nincs kategorizálva
- nincs kategorizálva Fantini Cosmi
- nincs kategorizálva Brockhaus HEUER
- nincs kategorizálva Bruder Mannesmann
- nincs kategorizálva Kaona
- nincs kategorizálva Auer Signal
- nincs kategorizálva Scotsman
- nincs kategorizálva Hikmicro
- nincs kategorizálva Pieps
- nincs kategorizálva Callpod
- nincs kategorizálva Dantherm
- nincs kategorizálva Laine
- nincs kategorizálva TELEX
- nincs kategorizálva Mikrotik
- nincs kategorizálva Skil
- nincs kategorizálva Gazelle
Legújabb útmutatók nincs kategorizálva
10 Április 2025
10 Április 2025
10 Április 2025
9 Április 2025
9 Április 2025
9 Április 2025
9 Április 2025
9 Április 2025
9 Április 2025
9 Április 2025