Használati útmutató CRUX CRM-01P

Olvassa el alább 📖 a magyar nyelvű használati útmutatót CRUX CRM-01P (1 oldal) a tolatókamera kategóriában. Ezt az útmutatót 2 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Oldal 1/1
Crux Interfacing Solutions • 21541 Nordhoff St., Unit C, Chatsworth, CA 91311
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
rev.082619
CRM-01P
RAM PROMASTER Rear Marker Light Camera
2014 - 2016
- Selectable Parking Guide Line with ON/OFF opon.
- With manually adjustable viewing angle.
- Includes all necessary installaon hardware.
- Maintains the OEM look of the Van.
PRODUCT FEATURES:
PARTS INCLUDED:
INSTALLATION DIAGRAM:
CRM-01P CAMERA EXTENSION CABLE INSTALLATION ACCESSORIES
*NOTE: To power the camera, tap power from the radio or RVC Interface or from the reverse light +12V. Connect the
Black wire to a solid chassis ground. For vehicles with manual transmission, we recommend tapping +12V power from
the reverse light.
PARKING LINES: Cut the Green loop wire turn OFF parking guide lines.
R
INTERFACING SOLUTIONS
Sightline
CAMERAS
1. Remove the center rear marker from the vehicle and unplug the lamp connector.
2. Insert the 4-pin barrel connector on the camera cable through the OE wire hole.
3. Mount the camera base to the vehicle using the nuts and bolts provided in the kit.
4. Route the rear marker light connector through the camera base and shroud.
5. Mount the camera shroud to the base using the screws provided.
6. Plug the rear marker light connector and install the rear marker on the camera shroud using the screws provided.
7. Plug the camera’s 4-pin aviaon style connector to the extension cable.
8. The camera has an oponal parking guide lines feature. To turn OFF the parking guide lines, cut the GREEN loop wire.
9. Route the camera extension cable from the rear of the vehicle to the monitor locaon. Use zip es or tape to secure it.
10. Plug the Yellow male RCA to the monitor’s camera input and the White RCA to mic input (if applicable).
11. Connect the camera’s power and ground (red and black wire) to the reverse light power wire or to a switched +12V power if you prefer to
use the camera even when the vehicle is not in reverse gear. A toggle switch is recommended to turn o the camera when not needed.
12. Test the camera before pung back the radio or any trim plates removed.
13. Adjust the camera angle if necessary.
INSTALLATION PROCEDURE:
GREEN Wire
Parking Guideline
(see Instructions below)
Extension Coax Cable
To Aftermarket Radio
Backup Camera Input
OR
Reverse Camera Interface
Backup Camera Input
(Yellow - Video)
(White - Mic) RED wire +12V (to Backup Light)
BLACK wire (Ground)
1

Termékspecifikációk

Márka: CRUX
Kategória: tolatókamera
Modell: CRM-01P

Szüksége van segítségre?

Ha segítségre van szüksége CRUX CRM-01P, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek




Útmutatók tolatókamera CRUX

CRUX

CRUX CMB-17C Útmutató

30 December 2025
CRUX

CRUX CMB-16K Útmutató

30 December 2025
CRUX

CRUX CMB-16G Útmutató

30 December 2025
CRUX

CRUX CMB-15S Útmutató

30 December 2025
CRUX

CRUX RVCCH-75DC Útmutató

14 Augusztus 2024
CRUX

CRUX RVCCH-75WTC Útmutató

13 Augusztus 2024
CRUX

CRUX CNS-03V Útmutató

13 Augusztus 2024
CRUX

CRUX CVW-07G Útmutató

12 Augusztus 2024
CRUX

CRUX RVCCH-75EC Útmutató

12 Augusztus 2024
CRUX

CRUX CNS-01N Útmutató

12 Augusztus 2024

Útmutatók tolatókamera

Legújabb útmutatók tolatókamera