Használati útmutató CyberPower CPS140BI
CyberPower
Accu
CPS140BI
Olvassa el alább 📖 a magyar nyelvű használati útmutatót CyberPower CPS140BI (2 oldal) a Accu kategóriában. Ezt az útmutatót 11 ember találta hasznosnak és 6 felhasználó értékelte átlagosan 4.3 csillagra
Oldal 1/2
140WattACMobile PowerInverter
UserGuide
Figure1.ProductFeature
2004-5-075/front K
Output Power 140 Watts Continuous
Output Voltage 120 Volts +/- 10%
Output Frequency 60 Hz
Output Waveform Simulated Sine Wave
Input Voltage 10.8 to 15.8 volts
Low Voltage Shutdown 10.5 volt
Problem Possible Cause Suggested Solutions
No AC output power
(Power indicator is not
illuminated)
Poor contact with lighter socket
Automotive electrical systems
requires ignition to be on.
Car s lighter soc ket fuse blown
Over-heating
Vehicle s battery below 10.8
volts.
Ensure the inverter adapter is securely
plugged into vehicle s lighter socket.
Replace the lighter socket if necessary.
Turn the vehicle ignition key to the
Accessory position.
Check the vehicle fuse panel and replace
the damaged fuse.
Allow inverter to cool down. Ensure that
there is adequate ventilation around the
unit and load is no more than 140 watts for
continuous operation.
Unplug the inverter and charge the vehicle
battery.
Short/Long Beep Your vehicle s battery input
voltage is below than 10.8 volt.
Vehicle s battery input voltage
is higher than 15.8 volt.
Inverter is overload.
Check vehicle s battery and ensure its
capacity. Change vehicle s battery if
necessary.
Check for your vehicle s battery
manufacturer guideline.
Reduce load to 140 watts max to maintain
regulation.
ContactScrew
Spring
ContactPin
Fuse
DecorativeRing
LighterAdapter
CPS140BI contains a fuse inside in the Lighter Adapter (see Figure 2) to protect the unit against
overloading. If the inverter draws more than 140 watts, the internal fuse may be blownto protect
the inverter, vehicle battery and the connected equipment. To replace the fuse, please follow the
instruction below:
1. Unplug the inverter from the power source.
2. Remove the Contact Screw from the Lighter Adapter.
3. Replace the 15 ampere fuse.
4. Reassemble the fuse, contact pin and contact screw carefully.
5. Ensure all pieces showed in Figure 2 are installed in the sequence shown.
*Note: For in-warranty units, the replacement fuse can be obtained from CyberPower
Technical Support. For out-of-warranty units, the replacement 15 ampere fuse can be obtained
from most electronic supply retailers.
WARRANTY RETURN
Cyber Power Systems, Inc.
5555 12th Avenue East, Suite 110, Shakopee, MN 55379, U.S.A.
TEL: (952) 403-9500 FAX: (952) 403-0009 Toll-Free: (877) 297-6937
E-mail: sales@cyberpowersystems.com Web: www.cyberpowersystems.com
Entire contents copyright 2004 Cyber Power Systems, Inc.
All rights reserved. Reproduction in whole or in part without permission is prohibited
K01-BT14000
C
2004-5-075/ Kback
Termékspecifikációk
| Márka: | CyberPower |
| Kategória: | Accu |
| Modell: | CPS140BI |
Szüksége van segítségre?
Ha segítségre van szüksége CyberPower CPS140BI, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek
Útmutatók Accu CyberPower
24 December 2024
24 Szeptember 2024
24 Szeptember 2024
24 Szeptember 2024
24 Szeptember 2024
24 Szeptember 2024
21 Szeptember 2024
21 Szeptember 2024
21 Szeptember 2024
21 Szeptember 2024
Útmutatók Accu
- Accu FeinTech
- Accu Speed-Link
- Accu Ultron
- Accu Sungrow
- Accu Fluke
- Accu SKROSS
- Accu Vetus
- Accu Skil
- Accu Duracell
- Accu McCulloch
- Accu TCW Technologies
- Accu Abus
- Accu Fxlion
- Accu Epson
- Accu Ventev
Legújabb útmutatók Accu
3 Április 2025
10 Január 2025
4 Január 2025
3 Január 2025
1 Január 2025
31 December 2025
31 December 2025
31 December 2025
30 December 2025
30 December 2025