Használati útmutató CyberPower EC650LCD
CyberPower
UPS
EC650LCD
Olvassa el alább 📖 a magyar nyelvű használati útmutatót CyberPower EC650LCD (2 oldal) a UPS kategóriában. Ezt az útmutatót 14 ember találta hasznosnak és 7.5 felhasználó értékelte átlagosan 3.8 csillagra
Oldal 1/2
EC450G / EC550G / EC750G
EC650LCD / EC850LCD
User Manual ’s
K01-0000 - 855 00
Thank you for selecng the CyberPower UPS product. This UPS is designed to provide unsurpassed power protecon, operaon and
performance during the lifeme of the product. Please take a few minutes to register your product by vising:
CyberPowerSystems.com/registration. Registraon ceres your product's warranty, conrms your ownership in the event of a
product loss or the and entles you to free technical support.
(SAVE THESE INSTRUCTIONS)
This manual contains important safety instrucons. Please read and follow all instrucons carefully during installaon and operaon of
the unit. Read this manual thoroughly before aempng to unpack, install, or operate your UPS.
CAUTION! To prevent the risk of re or electric shock, install in a temperature and humidity controlled indoor area ee of fr
conducve contaminants. (Please see specicaons for acceptable temperature and humidity range).
CAUTION! To reduce the risk of electric shock, do not remove the cover. There are no user serviceable parts inside.
CAUTION! Hazardous live parts inside can be energized by the baery even when the AC input power is disconnected.
CAUTION! The UPS must be connected to an AC power outlet with fuse or circuit breaker protecon. Do not plug into an outlet
that is not grounded. If you need to de-energize this equipment, turn o and unplug the unit.
CAUTION! To avoid electric shock, turn o the unit and unplug it from the AC power source before installing a computer component.
CAUTION! Not for use in a computer room as dened in the Standard for the Protecon of Electronic Computer/Data Processing
Equipment, ANSI/NFPA 75.
CAUTION! To reduce the risk of re, connect only to a circuit provided with 20 amperes maximum branch circuit over current
protecon in accordance with the Naonal Electric Code, ANSI/NFPA 70.
DO NOT USE FOR MEDICAL OR LIFE SUPPORT EQUIPMENT! CyberPower Systems does not sell products for life support or medical
applicaons. use in any circumstance that would aect operaon and safety of life support equipment, any medical DO NOT
applicaons or paent care.
DO NOT USE WITH OR NEAR AQUARIUMS! To reduce the risk of fire or electric shock, do not use with or near an aquarium.
Condensaon from the aquarium can cause the unit to short out.
DO NOT USE THE UPS ON ANY TRANSPORTATION! To reduce the risk of re or electric shock, do not use the unit on any
transportaon such as airplanes or ship. Th eect of shock or vibraon caused during transit and the damp environment can cause e
the unit to short out.
UNPACKING
Inspect the UPS upon receipt. The box should contain the following:
(a) UPS unit (b) User’s manual USB A+B type cable(c)
*PowerPanel® Personal soware is available as a free download at:CyberPowerSystems.com/products/soware.
HOW TO DETERMINE THE POWER REQUIREMENTS OF YOUR EQUIPMENT
1. Ensure that the equipment plugged into t UPS y (450VA/260W for EC450G, he does not exceed the UPS unit’s rated capacit
550VA/330W for EC550G, 750VA/450W for EC750G, 650VA/ 0W for EC650LCD, and 850VA/510W for EC850LCD). If the rated 39
capacies of the unit are exceeded, an overload condion may occur and cause the UPS unit to shut down or the circuit breaker to
trip.
2. There are many factors that can aect the amount of power that your electronic equipment ll require. For opmal system wi
performance keep the load below 80% of the unit’s rated capacity.
HARDWARE INSTALLATION GUIDE
1. Your new UPS may be used immediately upon receipt. However, aer receiving
a new UPS, to ensure the baery’s maximum charge capacity, it is
recommended that you charge the baery for at least 8 hours. Your UPS is
equipped with an auto-charge feature. When the UPS is plugged into an AC
outlet, the baery will automacally charge whether the UPS is turned on or
turned o.
Note: This UPS is designed with a safety feature to keep the system from being turned on during shipment. Th rst me you turn e
the UPS on, you will need to have it connected to AC power or it will not power up.
2. With the UPS unit turned o and unplugged, connect your computer, monitor, and any other peripherals requiring baery backup
into the baery power supplied outlets. Plug the other peripheral equipment (e.g. printer, scanner, speakers, etc.) into the full-time
surge protecon outlets. DO NOT plug a laser printer, paper shredder, copier, space heater, vacuum cleaner, sump pump, or other
large electrical device into the Baery and Surge Protected Outlets“ ”. The power demands of these devices will overload and
possibly damage the unit.
3. Plug the UPS into a 2 pole, 3 wire ground receptacle (wall outlet). Make sure the wall branch outlet is ed
protected by a fuse or circuit breaker and does not service equipment with large electrical demands (e.g. air
condioner, refrigerator, copier, etc.). The warranty prohibits the use of extension cords, outlet strips,
and surge strips in conjuncon with the UPS unit.
4. Press the power switch to turn the unit on. The Power On indicator light will illuminate green twice. and the unit will “beep”
5. If an overload is detected, an audible alarm will sound and the unit will emit one long beep. To correct this, turn the UPS o and
unplug at least one piece of equipment from the battery power supplied outlets. Make sure the circuit breaker is depressed and
then turn the UPS on.
6. To maintain opmal battery charge, leave the UPS plugged into an AC outlet at all mes.
7. To store UPS for an extended period of me, cover it and store with the baery fully charged. While in storage, recharge the the
baery every three months to ensure opmal baery life.
8. Ensure the wall outlet and UPS are located near the equipment being aached for proper accessibility.
DESCRIPTION
1. Battery and Surge Protected Outlets
The unit has baery powered/surge suppression outlets to ensure temporary uninterrupted operaon of your equipment during a
power failure. (DO NOT plug a laser printer, paper shredder, copier, space heater, vacuum cleaner, sump pump, or other large
electrical device into the Baery and Surge Protected Outlets.“ ” The power demands of these devices will overload and
possibly damage the unit.)
2. Full-Time Surge Protecon Outlets / ECO Controlled Outlets
The unit has surge suppression outlets to provide surge and line noise protecon. Three of the surge-only outlets are also ECO
controlled outlets.
3. ECO Indicator
ECO Indicator shows the condion of ECO funcon. For more informaon, refer to secon. ECO Funcon Setup
4. Power On Indicator (green)
This LED is illuminated when the ulity power is normal and the UPS outlets are providing power, free of surges and spikes.
5. Power Switch
To turn the UPS , press the power buon for approximately 2 seconds - you will hear a constant tone (1 second) - and release ON
aer a short beep.
To turn the UPS , press the power buon for approximately 2 seconds - you will hear a constant tone (1 second) - and release OFF
aer two short beeps.
Alarm seng: The audible alarm can be turned by double click the POWER buon. The default seng is for the Alarm O or On
On. To turn the Alarm O, double click the buon. You will hear two short beeps when the Alarm is turned o . To turn the Alarm ff
back On, double click the buon. You will hear a single short beep when the Alarm is turned on. *When the Alarm is turned O,
there will be no audible nocaon when the UPS reaches a low baery state.
6. Mode Switch (EC650LCD and EC850LCD only)
Press the Mode Switch for approximately 3 seconds to enter setup mode to select four funcons: Ulity High Voltage Range,
Ulity Low Voltage Range ECO ON/OFF and LCD sleep ON/OFF. When a function is selected, press Mode Switch for 3 seconds to , ,
view opons. When an opon is selected, wait for 8 seconds for the seng to be conrmed. Aer the seng has been
conrmed the LCD screen will leave setup mode and go back to status display. If there is no acon for 8 seconds during setup, the
LCD will also leave setup mode and go back to the status display.
a. Ulity High Voltage Range: Adjust the value of high voltage range.
b. Ulity Low Voltage Range: Adjust the value of low voltage range.
c. ECO: Eon/EoF (ON/OFF) Turn on or turn off ECO funcon. more informaon, refer to section. : For ECO Funcon Setup
d. LCD L1/L0 (ON/OFF): :
* When LCD is set to L1, LCD will be always ON When LCD is set to , LCD will dim if untouched for 1 minute. . L0
* In baery mode, LCD is always on regardless if the setng is L1 or L0.
ECO Buon (EC450G, EC550G, and EC750G only)
Press ECO buon for 3 seconds to turn on or turn o ECO funcon in line mode.
7. Circuit Breaker
Located on the side of the UPS, the circuit breaker serves to provide overload and fault protecon.
8. USB Port to PC
The USB port allows connecon and communicaon between the USB port on the computer and the UPS unit. The UPS
communicates its status to the PowerPanel ® Personal soware. The USB port is also used for operang the UPS in ECO mode. For
more informaon, refer to secon. ECO Funcon Setup
9. ECO Mode, Surge Protected Outlets
ECO Mode outlets automacally cut power to peripherals when your computer is in Sleep mode or is turned o (USB connecon
required).
10. Outlets Designed for AC Adapters
The UPS unit has 4 widely-spaced outlets so AC power adapters can be plugged into the UPS without overlapping or blocking
adjacent outlets.
ECO FUNCTION SETUP
ECO Funcon
When the ECO funcon is acve the UPS can detect whether the PC that is connected to the USB port is turned on or o. If the PC is
turned o, the UPS will turn o the ECO controlled outlets and cut power to the devices connected to them in order to save power.
Generally, these are peripherals that are not used when the PC is not turned on.
ECO Controlled Outlets
Three of the surge-only outlets are also ECO controlled outlets. When that is connected to the USB port is turned o, UPS the PC the
will turn o the ECO controlled outlets to save energy.
ECO Setup
1. The factory default seng is OFF. ECO mode can only be enabled/disabled and will only be acve when the UPS is receiving
ulity power and not in baery mode.
2. For the EC650/850LCD, press the Mode switch for approximately 3 seconds to enter setup mode and select the ECO funcon.
When the ECO funcon is selected, press the Mode switch for 3 seconds to turn the funcon ON or OFF. Once ON or OFF is
selected, wait 8 seconds for the seng to be conrmed and the LCD screen will return to status mode. For the EC450/550/750G,
press the ECO buon for 3 seconds to turn ON or OFF the ECO funcon.
3. When the ECO funcon is OFF, ulity power from the ECO outlets will always be on. When the ECO funcon is ON, ulity power
from the ECO outlets will turn o if the PC connected to the UPS via the USB port is turned o or if there is no PC is connected to
the UPS via USB.
ECO Indicator
The LED will be blinking when the ECO funcon is turned ON but the PC is either o or not connected. The LED will be solid if the ECO
funcon is turned on and the connected PC is on. The LED is o when the ECO funcon is disabled. See below table for more
informaon.
ECO Indicator
ECO Funcon
ECO Outlet Sta tus
Condion
Solid (green)
ON
With Ulity Power
When PC is ON and USB port on the UPS is connected,
Peripherals will receive power to operate.
Blinking
ON
Without Ulity
Power
When PC is OFF or the USB port on the UPS is not connected,
power to the Peripherals will be turned o.
OFF
OFF
Always with Ulity
Power
When PC is ON/OFF, Peripherals is always ON.
DEFINITIONS FOR ILLUMINATED LED INDICATORS
Power ON
Alarm
CONDITION
On
O
Normal
On
Beep twice
every 30 seconds
Ulity Failure- The UPS is providing power to baery power-supplied outlets from its
baery.
On
Rapid Beeping every
1/2 second
Ulity Failure- The UPS is providing baery power. Rapid beeping indicates the unit will
run out of power shortly.
O
Constant tone
Baery Overload - Occurs when connected equipment exceeds the listed capacity of the
UPS Turn the UPS o, unplug at least one piece of equipment from baery outlets, wait .
10 seconds, reset the circuit breaker and turn the unit on.
INPUT voltage meter: This meter measures the AC voltage that the UPS system is receiving
from the ulity wall outlet. The UPS is designed to connuously supply connected equipment
with stable output voltage. In the event of a complete power loss, severe brownout, or
over-voltage, the UPS relies on its internal baery to supply consistent 110/120 output voltage.
The INPUT voltage meter can be used as a diagnosc tool to idenfy poor-quality input power.
OUTPUT voltage meter: This meter measures, in real me, the AC voltage that the UPS system
is providing to the computer during normal AC/Ulity Power mode, and baery backup mode.
ESTIMATE RUN TIME: This displays the run me esmate of the UPS with the current battery
capacity and load.
NORMAL icon: This icon appears when the UPS is working under normal condions.
BATTERY icon: During a severe brownout or blackout, this icon appears and an alarm sounds (two short beeps followed by a pause) to
indicate the UPS is operang from its internal baery The alarm will connue to sound during a prolonged brownout or blackout. The .
BATT.CAPACITY meter will show one 20% capacity segment remaining to indicate the UPS's baery nearly out of power. You should is
save les and turn o your equipment immediately.
OVER LOAD icon: This icon appears and an alarm sounds to indicate the baery-supplied outlets are overloaded. To clear the
overload, unplug some of your equipment from the baery-supplied outlets unl the icon turns o and the alarm stops.
BATT. CAPACITY meter: This meter displays the approximate charge level of the UPS's internal baery in 20% increments. During a
blackout or severe brownout, the UPS switches to baery power (the BATTERY icon appears) and the baery charge level decreases.
LOAD CAPACITY meter : This meter displays the approximate output load level of the UPS baery outlets in 20% increments.
BASIC OPERATION
INSTALLING YOUR UPS SYSTEM
IMPORTANT SAFETY WARNINGS
DEFINITIONS FOR ILLUMINATED LCD INDICATORS
The LCD display indicates a variety
of UPS operational conditions. All
descriptions apply when the UPS is
plugged into an AC outlet and turned
on or when the UPS is on battery.
PRODUCT REGISTRATION
EC650LCD (8 outlets)
EC850LCD (12 outlets)
EC4 / EC550G (8 outlets) 50G
EC750G (12 outlets)
Termékspecifikációk
| Márka: | CyberPower |
| Kategória: | UPS |
| Modell: | EC650LCD |
Szüksége van segítségre?
Ha segítségre van szüksége CyberPower EC650LCD, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek
Útmutatók UPS CyberPower
31 Március 2025
31 Március 2025
31 Március 2025
16 Január 2025
4 Január 2025
4 Január 2025
31 December 2025
8 December 2024
8 December 2024
2 Október 2024
Útmutatók UPS
- UPS Hikvision
- UPS Altronix
- UPS Lenovo
- UPS Atlantis Land
- UPS Schneider
- UPS Block
- UPS Equip
- UPS GYS
- UPS Riello
- UPS Conceptronic
- UPS Online USV
- UPS PowerWalker
- UPS Dell
- UPS Murr Elektronik
- UPS Ikea
Legújabb útmutatók UPS
9 Április 2025
9 Április 2025
3 Április 2025
3 Április 2025
30 Március 2025
29 Március 2025
29 Március 2025
29 Március 2025
29 Március 2025
29 Március 2025