Használati útmutató Ergotron 24-235-085

Ergotron Multimédia adó 24-235-085

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Ergotron 24-235-085 (8 oldal) a Multimédia adó kategóriában. Ezt az útmutatót 3 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.3 csillagra

Letöltés PDF

Oldal 1/8

777-24-014-W-02 rev C

5 / 4

Tablet Management Cart

Set-up and Go Guide

Pages 1 - 4

Guide Set-up and Go

du chariot de gestion de tablettes

Page 5 - page 8

Guía para la con guración

y puesta en marcha

del carrito de gestión de tabletas

Páginas 9 - 12

Tablet Managementwagen – Anleitung

zum Aufbau und Gebrauch

Seite 13 - Seite 16

Carrello di gestione tablet – Guida

rapida all’installazione

Paginas 17 - 20

タブレットマネジメントカート

（Tablet Management Cart）のセ

ットアップおよび使用ガイド

21 ページ - 24 ページ

平板电脑管理手推车安装和使

用指南

5 页 - 28 页

Two Module

Management Carts

Chariots de gestion

à deux modules

Carritos de gestión

con dos módulos

Zwei-Modul-

Managementwagen

Carrelli di gestione

a due moduli

モジュール2個付きマネ

ジメントカート

两台模块管理手推车

777-24-014-W-02 rev C

1 / 4

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

1 2 3

Make sure the cart power cord is disconnected

from wall power supply before proceeding.

Unlock the module and open the doors.

1 Tablet Charging Set-up

Place the drawer up-side-down on the cart top. Line

up a tablet USB cable along numbers 1 to 8 on the

drawer as a way to measure out slack (represented

by dashed line).

Slide the drawer partially into the module. Recon-

nect the USB and DC cables and wrap the straps

around the cables.

Use a Phillips screwdriver to remove the two screws

located on the interior sides of the module; save

screws to reinsert later.

Route the tablet USB cable through the slots to

the back of the drawer maintaining the slack mea-

sured in previous step.

Slide the drawer completely into the module.

Insert the screws removed in step 2 and tighten.

Partially slide out the module drawer. You’ll need

to unplug two cables before sliding the drawer

completely out. Open the strap to access the two

cables.

Turn over the drawer. Wrap the excess USB cable

around the cable organizer.

Insert tablets into module. Connect the tablet

USB charging cables to the tablets. Repeat Steps

1 - 10 for the other modules.

Unplug the USB and DC power cables (push up on

the lever under the DC connector to release). The

drawer can now be removed.

Connect the USB cable to the corresponding USB

port. Repeat USB cabling steps 5 through 8 for the

rest of the tablets going into this module.

Follow Tablet Charging instructions  rst, then Sync Set-up Instructions on next page.

Tablet Charging

The power cord is used to turn

the Cart power on and o .

Charging occurs whenever the

cart power cord is connected

UNLESS a Mac or PC notebook

USB cable is connected to the

cart for syncing (see Tablet

Syncing Set-Up on the next page).

Tablet Management Cart

Set-up and Go Guide

The cart power cord acts as the connect/disconnect de-

vice switching power o and on.

1 / 28

777-24-014-W-02 rev C

2 / 4

1–16

LED - Indicators

Place your Mac or PC notebook, power adaptor and

a USB cable on the cart work top.

1 Tablet Charging Set-up

2 Tablet Syncing Set-up

Plug the USB and power adaptor cables into

the notebook; route the ends of the cables

down the side of the cart, and strap

the power adaptor into the re-

cessed area to store.

continued

Complete the Tablet Charging instructions before starting the Syncing Instructions.

Power Indicator – communicates sync and charge status with the following signals:

O = No power to the module.

On - solid = Tablets are charging.

On - slow blink = Computer is plugged into auxillary USB outlet and tablets are ready to sync or are syncing.

On - fast blink = Fault Status. Please make sure all cables are seated correctly within cable drawer. Contact Ergotron Customer

Support if problem continues.

Individual Status Indicators (ISI) – sequentialy numbered LEDs corresponding to each tablet in the module*:

Green = Fully charged.

Amber = Charging in progress.

Connect the notebook USB cable to the port

on the side of the cart.

Syncing Notebook to Tablets

The tablets will mount as USB devices when the included USB cable is connected to a host laptop via the USB port on the exterior of the module.

Apple iPad or iPod Touch devices will sync to a host laptop using iTunes. If the Mac or PC laptop power is on, and the laptop is running iTunes, the devices will sync to the laptop automatically when the USB

cable is connected from the laptop to the USB port on the exterior of the module. Please see included separate instructions for speci c setup of iTunes and your Apple devices.

For all other tablets, please reference your tablet manufacturer’s product guide for information or instructions about how to sync to a host laptop.

* If module is syncing all ISIs will be green.

Connect the notebook power adaptor into the

auxilary outlet on the side of the cart. Tuck

the access cables into the recessed area. Switch

on the notebook power to begin

syncing.

Tablet Management Cart

Set-up & Go Guide

2 / 28