Használati útmutató Geemarc AMPLICALL PSA100
Geemarc
nincs kategorizálva
AMPLICALL PSA100
Olvassa el alább 📖 a magyar nyelvű használati útmutatót Geemarc AMPLICALL PSA100 (2 oldal) a nincs kategorizálva kategóriában. Ezt az útmutatót 19 ember találta hasznosnak és 10 felhasználó értékelte átlagosan 4.4 csillagra
Oldal 1/2
The distance between both devices
cannot exceed 30 meters
AMPLICALL PSA 100
INSTALLATION
Fig. 1 Fig. 2 Fig. 3
Matière :
plastic PVC
2) Transmitter
1. Battery cover
2. Pessure sensor mat
Setting up the pressure sensor mat
1. Touch the edges of the pressure sensor mat until you
feel a hard piece of plastic, this is the small transmitter
that is inside. Open the opening that is kept shut by a
piece of double sided Velcro and get the transmitter out.
(Fig1)
2. Use a at screwdriver as a lever to open the battery
compartment. (Fig2)
3. Insert a coin cell battery CR2032 while observing the
correct polarity. (Fig.3)
4. Put the battery compartment back in place and make
sure the red LED light inside the transmitter lights up
when pressure is applied to the sensor mat.
5. Replace the transmitter in the opening on the edge of
the sensor mat before shutting it back with the piece of
double sided Velcro.
1. Unscrew the screw that is on the back of the wireless
receiver and that holds the cover of the battery
compartment in place before sliding open the battery
compartment. (Fig4)
2. Place three 1.5V batteries type LR14 (not included) in
the battery compartment while observing the correct
polarity, and place the battery compartment back in
place. (Fig5)
3. You can connect an AC adapter 6V DC 0.3A (not
included); plug length: 12mm; inside positive ID:
2.1mm; outside negative OD: 5.5mm) to the alert, and
install the batteries as backup in case of power failure.
Setting up the receiver
USING THE PSA100
PAIRING
TECHNICAL CHARACTERISTICS
(Fig 4)
(Fig 5)
The Amplicall PSA 100 is an easy-to-use device made up of
a pressure sensor mat connected to a signal transmitter, and
a wireless signal receiver.
As soon as pressure is being applied to the sensor mat, the
transmitter it is connected to will send a signal to the wireless
receiver which will immediately start ringing and ashing. The
receiver’s alarm volume can be set to high or low. The pressure
sensor mat can be placed in front of an entrance door or in a
corridor so that one can immediately be made aware of any
movement in the area.
The pressure sensor mat and wireless receiver are delivered
already paired. When setting them up for the rst time, you
should apply pressure on the sensor mat to make sure this
triggers the alarm, which ought to be placed less than 30
meters away.
1
2
Note: The receiver is wall mountable.
A. Drill two holes horizontally, 36 mm apart.
B. Insert two wall plugs xing into the two holes.
C. Screw two screws into the plugs, hang the receiver on the
support and slide it down to lock it.
1. Place the pressure sensor mat on a at surface.
2. If the power slide switch of the receiver is moved to the « CHIME
» position, the receiver will ring and ash once for 5 seconds
each time pressure is applied to the sensor mat.
3. If the power slide switch of the receiver is moved to the
« ALARM » position, the receiver will ring and ash once for 30
seconds each time pressure is applied to the sensor mat.
Note: The receiver will stop ringing and ashing if its power
slide switch is moved to the “OFF” position.
When not used, the power switch of the receiver should be moved
to the “OFF” position to prevent them from ringing and save battery
life.
You can pair up to 10 wireless receivers to a single pressure
sensor mat. To pair new receiver, you should follow the steps
below:
1.Move the receiver’s power slide switch to either the “ALARM” or
“CHIME” position. You will hear a tone. It indicates that the receiver
has been activated and is now in standby mode.
2. When in standby mode, you can use the tip of a pencil or a
screwdriver to press and hold the “learn” button that is on
the back of the wireless receiver for about 3 seconds. As
soon as you hear a short tone, you can release the “learn”
button. The wireless receiver is now in learning mode and
is ready to receive a pairing signal from your sensor mat’s
transmitter.
3. Move the power slide switch of your sensor mat’s transmitter
to either the “ALERT” or “ARM” position without applying
pressure to the mat.
4. If you hear four consecutive short tones coming from the
receiver, this means the pairing process has succeeded.
To unpair a wireless receiver, press and hold its “learn”
button for 12 seconds until you hear two long tones. This
indicates the receiver is no longer paired to any pressure
sensor mat.
Range: 30-meter
Frequency: 433.92Mhz
Ringer volume:
85dB (HI) or 70dB (LO) on the receiver
Power:
1 coin cell battery CR2032 for the transmitter
Three 1.5V batteries (type LR14) for the receiver
Up to 10 receivers for each transmitter
Radio frequency power: < 250mW
1
2
3 4
5
8
9
7
6
Pressure sensor mat and alarm
DESCRIPTION
Inside your gift box you should nd the below elements:
- 1 User guide
- 1 pressure sensor mat and its transmitter
- 1 wireless receiver( Batteries are not included) .
- A mains adapter is available as a spare part. (6V 0.3A)
Box Content
Wireless receiver
1. Volume control (HI/LO)
2,4. Visual indicators (Flash when
triggered by transmitter)
3. Visual indicator (Flashes when
triggered by transmitter/ Lights up
when batteries are low)
5. Loudspeaker
8. “Learn” paring button
9. Battery cover
10. Screw
11. Holes to mount device onto a wall
6. Power slide switch (Alarm/
o/chime)
7. DC adaptor socket
(6V DC/0.3A)
10
11
UGEnACPSA100
The middle LED (3) will start ashing to warn you that the battery
needs to be replaced.
En
Termékspecifikációk
| Márka: | Geemarc |
| Kategória: | nincs kategorizálva |
| Modell: | AMPLICALL PSA100 |
Szüksége van segítségre?
Ha segítségre van szüksége Geemarc AMPLICALL PSA100, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek
Útmutatók nincs kategorizálva Geemarc
11 December 2024
11 December 2024
11 December 2024
11 December 2024
30 Augusztus 2024
30 Augusztus 2024
30 Augusztus 2024
30 Augusztus 2024
30 Augusztus 2024
16 Augusztus 2024
Útmutatók nincs kategorizálva
- nincs kategorizálva Unitech
- nincs kategorizálva Fortinge
- nincs kategorizálva NWS
- nincs kategorizálva Unger
- nincs kategorizálva Syma
- nincs kategorizálva Portkeys
- nincs kategorizálva Getac
- nincs kategorizálva Medel
- nincs kategorizálva Boso
- nincs kategorizálva Ruark Audio
- nincs kategorizálva Bliss Outdoors
- nincs kategorizálva Dorma
- nincs kategorizálva Valore
- nincs kategorizálva Ibm
- nincs kategorizálva Roadinger
Legújabb útmutatók nincs kategorizálva
10 Április 2025
10 Április 2025
10 Április 2025
9 Április 2025
9 Április 2025
9 Április 2025
9 Április 2025
9 Április 2025
9 Április 2025
9 Április 2025