Használati útmutató NUVO Halter 60/7692
NUVO
Megkönnyebbülés
Halter 60/7692
Olvassa el alább 📖 a magyar nyelvű használati útmutatót NUVO Halter 60/7692 (2 oldal) a Megkönnyebbülés kategóriában. Ezt az útmutatót 14 ember találta hasznosnak és 7.5 felhasználó értékelte átlagosan 4.9 csillagra
Oldal 1/2
FOR YOUR SAFETY
WARNING: BE SURE THE ELECTRICITY TO THE WIRES YOU ARE
WORKING ON IS SHUT OFF; EITHER THE FUSE IS REMOVED OR
THE CIRCUIT BREAKER IS SHUT OFF.
GENERAL
You don’t need special tools to install this xture. Be sure to follow
the steps in the order given. Under no circumstances should a xture
be hung on house electrical wires, nor should a swag type xture be
installed on a ceiling which contains a radiant type heating system.
Read instructions carefully. If you are unclear as to how to proceed,
consult a qualied electrician.
NOTE: Proper wiring is essential for the safe operation of this xture.
FIXTURE ASSEMBLY
Carefully remove the xture from the carton and check that all parts
are included as shown in gure. Be careful not to misplace any of the
screws or parts, which are needed to install this xture.
STEP 1: Adjust the arms to a proper position. Put the shade over the
hook of the arms.
STEP 2: Thread tube. Carefully pass the wires through each tube during
assembly. Repeat this step until the desired hanging height is reached.
STEP 3: Thread the tube into canopy and body.
INSTALLATION
IMPORTANT: Do not attach xture directly to outlet box.
STEP 1: Thread mounting screw into the match hole of cross bar.
STEP 2: Secure the cross bar to outlet box with outlet box screws.
GROUNDING INSTRUCTIONS
STEP 1: Insert the green grounding screw into the hole with two raised
dimples on the mounting bar. Wrap the ground wire from the xture (if
supplied) around the green grounding screw, then connect it to ground
wire from the outlet box (if not xed on the outlet box) using a wire
connector (not supplied). If ground wire from the xture is not supplied,
wrap the ground wire (if not xed on the outlet box) from the outlet box
around the green grounding screw and tighten it.
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE
POWER SUPPLY WIRES.
STEP 2: Take note of the color of the wire(s) on your xture. Identify
which group your xture wire(s) falls into and connect the wires
according to the directions below:
GROUP A:
Connect to Black House Wire
GROUP B:
Connect to White House Wire
BLACK WHITE
* PARALLEL WIRE (round & smooth) * PARALLEL WIRE (square & ridged)
WHITE OR GREY WITH TRACER WHITE OR GREY WITHOUT TRACER
BROWN, GOLD OR BLACK
WITHOUT TRACER
BROWN, GOLD OR BLACK
WITH TRACER
NOTE: When parallel wire (SPT-I & SPT-2) is used, the tracer wire is
square shaped or ridged and the less tracer wire is round in shape or
smooth (seen best when viewed from wire end.)
STEP 3: Take your xture wire(s) from group A and place evenly against
the black wire from the outlet box. Do NOT twist wires together before
using wire connectors.
STEP 4: Fit a wire connector over the wires and screw the connector
clockwise until you feel rmness.
STEP 5: Try gently to pull the connector off the wires. If you can pull the
connector off, carefully re-do steps 3 and 4 as above, and check again
for a rm connection.
STEP 6: Connect the xture wire from group B to the white wire from
the outlet box in the same manner. Make sure no bare wires can be
seen outside wire connectors.
FINAL ASSEMBLY
STEP 1: After wires are connected, tuck them carefully inside outlet
box. Raise canopy allowing the mounting screw to protrude through the
hole in the canopy, and secure with ball nuts.
STEP 2: Install lamps (not included). Please do not exceed the
maximum capacity recommended on the socket.
CLEANING
To clean, wipe xture with a soft cloth. Clean glass with a mild soap.
Do not use abrasive materials such as scouring pads or powders, steel
wool or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts. Be sure to use exact wording from illustration when
ordering parts.
FIGURE
Line art shown may not exactly match the xture enclosed. However, the installations
do apply to this xture.
La ilustración puede no concordar exactamente con la pieza enviada. Sin embargo,
las instalaciones sí aplican para esta pieza.
Les images peuvent ne pas correspondre exactement au luminaire de la boîte.
Par contre, les directives d’installation s’appliquent au luminaire.
INSTALLATION AND SAFETY INSTRUCTIONS
ITEM NO: 60-7691, 60-7692, 60-7693
ARTÍCULO Nº: 60-7691, 60-7692, 60-7693
ARTICLE N°: 60-7691, 60-7692, 60-7693
Outlet Box Screws
Ball Nut
Outlet Box
White Supply Wire
Ribbed Fixture Lead
Green Ground Screw
Body
Canopy
Tube
Tube
Tube
Tube
Mounting Bracket
Black Wire Connection
Wire Connector
Smooth Fixture Lead
Lamp
Iron plate
Ball Nut
© Copyright 2022 Satco Products, Inc. 9/22 v1.0
Termékspecifikációk
| Márka: | NUVO |
| Kategória: | Megkönnyebbülés |
| Modell: | Halter 60/7692 |
Szüksége van segítségre?
Ha segítségre van szüksége NUVO Halter 60/7692, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek
Útmutatók Megkönnyebbülés NUVO
5 Április 2025
5 Április 2025
5 Április 2025
5 Április 2025
5 Április 2025
5 Április 2025
5 Április 2025
5 Április 2025
5 Április 2025
5 Április 2025
Útmutatók Megkönnyebbülés
- Megkönnyebbülés Heirt
- Megkönnyebbülés Livex Lighting
- Megkönnyebbülés Gira
- Megkönnyebbülés Denver
- Megkönnyebbülés Delock Lighting
- Megkönnyebbülés Pauleen
- Megkönnyebbülés Trio Lighting
- Megkönnyebbülés Time 2
- Megkönnyebbülés PowerPlus
- Megkönnyebbülés Sea&Sea
- Megkönnyebbülés Planet
- Megkönnyebbülés Sengled
- Megkönnyebbülés Wiesenfield
- Megkönnyebbülés DiO
- Megkönnyebbülés American DJ
Legújabb útmutatók Megkönnyebbülés
9 Április 2025
9 Április 2025
9 Április 2025
8 Április 2025
8 Április 2025
8 Április 2025
7 Április 2025
5 Április 2025
5 Április 2025
5 Április 2025