Használati útmutató Paasche FP-4P

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Paasche FP-4P (2 oldal) a nincs kategorizálva kategóriában. Ezt az útmutatót 8 ember találta hasznosnak és 4.5 felhasználó értékelte átlagosan 4.8 csillagra

Oldal 1/2
INSTRUCTION AND PARTS LIST FP-4P 2/26/2018
Paasche Airbrush Company
9511 58th Place Kenosha, WI 53144
Website: paascheairbrush.com
E-Mail: info@paascheairbrush.com
Comes with LN-1/32 (Assembled) and LN-1/64, 3/64, and 1/16 Nibs loose
Total Length of Flow Pencil is 5 -1/2 inches.
Printed in the U.S.A.
INTRODUCTION:
The FP-4P Flow Pencil is used extensively by Cake Artists,
Bakers, and Home Bakers to decorate their Cakes, Cupcakes,
Cookies,etc. The Flow Pencil is easy to control and operate.
MIXING :
1. Proper mixing of Royal Icing & Butter Cream is essential for
continuous and uninterrupted flow.
2. Experiment with thinning of Icing for best flow.
3. Do not mix Icing in cup of Flow Pencil, use a separate
container and pour into cup only when Icing is at proper
consistency.
LOADING ICING: ( Tighten adjusting screw at rear of flow
pencil before loading Icing)
1. Remove FP-5 Cover, and pour premixed Icing into cup 3/4
full, Hold lid firmly and push plunger into cup, Pressure will
build and plunger will rise, thread lid onto cup.
2. Turning the MU-72 Adjusting Screw will control the
movement of the MU-65 Finger Lever Assembly which
controls the flow of Icing.
OPERATION:
1. Hold the FP-4P Flow Pencil in your hand as you would a
pencil or brush and place your finger lightly over the MU-65
Finger Lever. When ready to begin piping, pull back on the
MU-65 Finger Lever, when the icing begins to flow raise
the pencil up and pull in a backward motion off the surface
slightly.
2. Regulate the flow to the desired feed rate by turning
MU-72 Adjusting Screw.
3. When the plunger gets closer to the cap the flow rate will
slow down.
4. Practice on a Cake board before working on a actual cake.
5. Correct adjustment of controls and skill of operation will result
in uninterrupted and continuous piping.
CARE AND CLEANING:
1. Before storing FP-4P Flow Pencil clean it thoroughly. Rinse
cup and lid in hot water to clean out Icing,remove nib and clean
in hot water, wipe dry.
2. MU-49L Needle is held in position by MU-57 Needle Chuck
and VL-141 Locknut. Remove the needle by unscrewing the
MU-71 Handle and removing the spring. Loosen the VL-141
Locknut and then remove the needle for cleaning.
ADJUSTING OR REPLACING WORN PACKING WASHER:
1. If PTFE Packing-#6 becomes worn or loose it must be
tightened or replaced.
2. You will need a small screwdriver to remove or tighten the
Packing Nut.
3. When replacing your PTFE Packing press Packing onto the
Packing Nut-#6. Use a small screwdriver to tighten packing nut
into shell until it is tight then back out one-half turn, may vary.
4. Now insert needle - you should feel a slight resistance. If too
loose or too tight adjust the Packing Nut with screwdriver until
you feel some slight resistance.
5. Now completely re-assemble guts of Flow Pencil.
CAUTION: OVER TIGHTENING CUP WILL
CAUSE TRIGGER TO MALFUNCTION.
WARNING: Follow all safety precautions.
CAUTION: Never point flow pencil at face when pressurized.
FP-4P
(Pressure Fed)
Flow Pencil
OPERATING INSTRUCTIONS & REPLACEMENT PARTS

Termékspecifikációk

Márka: Paasche
Kategória: nincs kategorizálva
Modell: FP-4P

Szüksége van segítségre?

Ha segítségre van szüksége Paasche FP-4P, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek