Használati útmutató Projecta BLT100
Projecta
Akkumulátor töltő
BLT100
Olvassa el alább 📖 a magyar nyelvű használati útmutatót Projecta BLT100 (4 oldal) a Akkumulátor töltő kategóriában. Ezt az útmutatót 11 ember találta hasznosnak és 6 felhasználó értékelte átlagosan 4.8 csillagra
Oldal 1/4

6 & 12V BATTERY
100 AMPS
LOAD TESTER
P/No. BLT100

CAUTION- BATTERIES PRODUCE EXPLOSIVE GASES,
TO REDUCE THE RISK OF EXPLOSION OR INJURY
ALWAYS ENSURE:
• No sparks or ames are present
• Eye protection is worn
• All vehicle or battery manufacturers instructions are followed
• Beware of moving parts
NOTE
The LOAD switch must not be pressed for longer than 10 seconds at a time, or
the product may be damaged.
When operating the unit for the rst time it is normal for a small amount of smoke
to develop as the lubricants used in the manufacturing process burn off.
Specications
Battery Load Test: 6 & 12V Lead Acid Batteries
Load: 100Amp @ 12V
50Amp @ 6V
Maximum Load ‘ON’ Time: 10 Seconds
Recommended Cool Down Time: 2 Minutes
Capacity Range: 200-1000CCA
Voltage Measured: 0-16V

Operating Instructions
Battery Load Test
1. Connect the RED clamp to the Positive (+) battery terminal or post.
2. Connect the BLACK clamp to the Negative (-) battery terminal or post.
If testing a battery in the vehicle, ensure the engine and all loads are’OFF’.
3. Note the batteries open circuit Voltage (OCV).
4. Press the ‘LOAD’ switch for 10 Seconds. Before releasing the ‘LOAD’
switch read the meter to determine the battery’s condition or approximate
capacity (For 12V batteries 200-1000CCA) & note the battery’s Voltage
while under load (Load Volts).
Charging System Test (12 Volt Vehicles)
1. Connect the RED clamp to the Positive (+) battery terminal or post.
2. Connect the BLACK clamp to the Negative (-) battery terminal or post.
Ensure the load tester and cables are clear of any moving parts.
3. Start the vehicle’s engine and operate at a fast idle speed, keep all accessorises,
lights & heater fan ‘OFF’.
4. Note the battery voltage, which should be in the green section of the charging
test, between 13.6 - 15 Volts, this indicates that the alternator’s regulator is
functioning correctly.
5. Turn ‘ON’ the vehicle’s head lights, heater fan or any other accessories,
the battery voltage should remain higher than 13.6 Volts, indicating that
the alternator is generating sufcient current.
Termékspecifikációk
Márka: | Projecta |
Kategória: | Akkumulátor töltő |
Modell: | BLT100 |
Szüksége van segítségre?
Ha segítségre van szüksége Projecta BLT100, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek
Útmutatók Akkumulátor töltő Projecta
16 Szeptember 2024
13 Szeptember 2024
5 Szeptember 2024
2 Szeptember 2024
3 Augusztus 2024
3 Augusztus 2024
3 Augusztus 2024
31 Július 2024
29 Július 2024
27 Július 2024
Útmutatók Akkumulátor töltő
- Akkumulátor töltő Camelion
- Akkumulátor töltő Venom
- Akkumulátor töltő Lifegoods
- Akkumulátor töltő Tecmate
- Akkumulátor töltő Media-Tech
- Akkumulátor töltő Anker
- Akkumulátor töltő Zipper
- Akkumulátor töltő Outspot
- Akkumulátor töltő Webasto
- Akkumulátor töltő Hoymiles
- Akkumulátor töltő Olympus
- Akkumulátor töltő SWIT
- Akkumulátor töltő Osram
- Akkumulátor töltő LVSUN
- Akkumulátor töltő Dometic
Legújabb útmutatók Akkumulátor töltő
9 Április 2025
9 Április 2025
9 Április 2025
3 Április 2025
3 Április 2025
3 Április 2025
3 Április 2025
31 Március 2025
30 Március 2025
26 Március 2025