Használati útmutató Projecta BLT300

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Projecta BLT300 (4 oldal) a Akkumulátor töltő kategóriában. Ezt az útmutatót 6 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Oldal 1/4
6/12/24 VOLT CARBON PILE
1000 AMP
LOAD TESTER
P/No. BLT300
CAUTION – BATTERIES PRODUCE EXPLOSIVE GASES, TO REDUCE THE RISK
OF EXPLOSION OR INJURY ALWAYS ENSURE:
No sparks or flames are present
Eye protection is worn
All vehicle or battery manufacturer’s instructions are followed
The load is “OFF” before connection or disconnection
Correct polarity, do not reverse connect
Beware of moving engine parts
NOTE
Carbon pile load testers produce a great amount of heat while the load is ‘ON’, do not apply the load for
more than 20 seconds at a time and allow time to cool between tests.
When operating the unit for the first time it is normal for a small amount of smoke to develop as the
lubricants used in the manufacturing process burn off.
SPECIFICATIONS
P/No. BTL300
Tests: Volts (0–24VDC)
6/12/24V Lead Acid Batteries
Battery Range: Up to 2000CCA (320Ah)
Test Load: Adjustable Carbon Pile
0–1000 AMPS
Maximum Load ‘ON’ Time: 20 seconds
Recommended Cool
Down Time: 2 minutes
Test time alert: Buzzer sounds after 15 sec
Cable length: 1400mm
Size: 350mm x 355mm x 175mm
Weight: 8.4kg
OPERATING INSTRUCTIONS
Battery Load Test
1. Connect the RED clamp to the Positive (+) battery terminal or post
2. Connect the BLACK clamp to the Negative (-) battery terminal or post.
Note: If testing a battery in the vehicle, ensure the engine and all loads are‘OFF’.
3. Check the battery’s open circuit voltage (OCV) on the DC Volt meter.
If the needle is in the green section of the ‘State of Charge’ scale (above 6.5V, 12.5V, 24.5V) the battery
has sufficient charge to test.
If the needle is in the red section (below 6.5V, 12.5V, 24.5V) the battery needs to be fully charged
before testing.
4. Determine the battery’s rated capacity in Cold Cranking Amps (CCA) or Amp hours (Ah) and calculate the
correct load current:
Cranking batteries with: Load current = 1/2 the CCA rating
Deep Cycle Batteries with: Load current = 3 x Ah rating
5. Turn the ‘Load Control Knob’ clockwise until the correct load current is reached on the DC Amps meter.
6. After 15 seconds the buzzer will sound to indicate the correct test time, immediately read the DC Volt
meter.
If the needle is in the green area of the ‘Battery Test’ scale the battery has passed the test.
If the needle is in the red area the battery has failed the test, quickly reduce the load current until the
needle moves back into the green area, and then read the approximate battery capacity in Ah or CCA
from the DC Amps meter.
ONCE THE METER HAS BEEN READ THE LOAD MUST BE TURNED OFF
IMMEDIATELY TO PREVENT OVERHEATING – TURN THE LOAD CONTROL
KNOB FULLY ANTI-CLOCKWISE.
Note: Battery ouput varies due to temperature change, the ‘Battery Test’ scale has four temperature
calibrations (21o, 10o, -1oand -18oCelcius). Use the closest scale to the approximate ambient temperature.

Termékspecifikációk

Márka: Projecta
Kategória: Akkumulátor töltő
Modell: BLT300

Szüksége van segítségre?

Ha segítségre van szüksége Projecta BLT300, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek




Útmutatók Akkumulátor töltő Projecta

Projecta

Projecta IC2500W Útmutató

16 Szeptember 2024
Projecta

Projecta BLT700 Útmutató

13 Szeptember 2024
Projecta

Projecta HDBM4000 Útmutató

5 Szeptember 2024
Projecta

Projecta PC2100 Útmutató

2 Szeptember 2024
Projecta

Projecta HDBC35 Útmutató

3 Augusztus 2024
Projecta

Projecta IC5000 Útmutató

3 Augusztus 2024
Projecta

Projecta HDBC20 Útmutató

3 Augusztus 2024
Projecta

Projecta IC2500 Útmutató

31 Július 2024
Projecta

Projecta IC1500L Útmutató

29 Július 2024
Projecta

Projecta BM320 Útmutató

27 Július 2024

Útmutatók Akkumulátor töltő

Legújabb útmutatók Akkumulátor töltő