Használati útmutató Projecta HDBT252
Projecta
nincs kategorizálva
HDBT252
Olvassa el alább 📖 a magyar nyelvű használati útmutatót Projecta HDBT252 (8 oldal) a nincs kategorizálva kategóriában. Ezt az útmutatót 9 ember találta hasznosnak és 5 felhasználó értékelte átlagosan 4.3 csillagra
Oldal 1/8

P/No. HDBT252
Tray Fitting Instructions to suit Auxiliary battery for
Mazda BT50 B3000 Automatic/Ford Ranger PJ–PK Automatic
Years: Jan 2007 – Oct 2011
Models: WLT – 2.5 Litre Turbo Diesel & 3.0 Litre Diesel
HEAVY DUTY DUAL BATTERY TRAY

2
IMPORTANT SAFETY INFORMATION
Please read this instruction thoroughly before fitting the tray.
This product is recommend to be fitted by a workshop or qualified mechanical person.
WARNINGS
• Before installation, make sure that the vehicle is stationary and the wheels chocked.
• Be careful when laying wires, not to cause any electrical shorts or wire breakage.
• After installation ensure the bonnet can close without hitting the newly installed battery
and battery tray.
SPECIFICATIONS
Max Battery Size (mm) L265 x W174 x H220
Max Battery Weight 18Kg
Recommended batteries Exide LCS 24-86, Exide ORBITAL ORB34DC & Century NS70T
Approximate fitting time 1.5 hours
Special tools None required
Recommended Dual IDC25, DBC100, DBC150, VSR100 or VSR200
Battery System
Tray Location Engine Bay, Passenger Side near radiator support
KIT INCLUDES
Hardware
2 x M6 Bolt Countersunk
5 x M6 Nut
5 x M6 Bolts Hex
1 X M8 Bolt
5 x 150mm Cable tie
Special
Top Mount
Tray
J Bolts
Computer Mount

1. Make sure that the vehicle is stationary, the engine is switched off and cool.
Disconnect the negative battery terminals from the main battery.
2. Your Auxiliary tray will be located between the passenger side headlight and air
cleaner. Remove the rear M8 bolt with large flange located on inner guard where
you will locate tray, in between the headlight and air cleaner and retain.
3. Move wiring loom from the same position.
4. Remove Computer mounting bracket from inner guard.
5. Remove wiring and relay from bracket.
6. Remove computer from bracket by removing 2 x M6 nuts and removing hold
down bracket.
7. Bolt computer to new computer mount, using top clamp.
8. Bolt computer mount to side of tray using 2 x M6 bolts Countersunk and
M6 Whizlocks.
3
FITTING INSTRUCTIONS
Termékspecifikációk
Márka: | Projecta |
Kategória: | nincs kategorizálva |
Modell: | HDBT252 |
Szüksége van segítségre?
Ha segítségre van szüksége Projecta HDBT252, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek
Útmutatók nincs kategorizálva Projecta
2 Október 2024
9 Augusztus 2024
5 Augusztus 2024
4 Augusztus 2024
3 Augusztus 2024
1 Augusztus 2024
31 Július 2024
31 Július 2024
29 Július 2024
29 Július 2024
Útmutatók nincs kategorizálva
- nincs kategorizálva Helix
- nincs kategorizálva SpeakerCraft
- nincs kategorizálva Enttec
- nincs kategorizálva Nero
- nincs kategorizálva Tripp
- nincs kategorizálva Kodak
- nincs kategorizálva Kyocera
- nincs kategorizálva Winix
- nincs kategorizálva Arlec
- nincs kategorizálva Ursus Trotter
- nincs kategorizálva Pippi
- nincs kategorizálva Insta360
- nincs kategorizálva Maxdata
- nincs kategorizálva Aerial
- nincs kategorizálva Bicker Elektronik
Legújabb útmutatók nincs kategorizálva
10 Április 2025
10 Április 2025
10 Április 2025
9 Április 2025
9 Április 2025
9 Április 2025
9 Április 2025
9 Április 2025
9 Április 2025
9 Április 2025