Használati útmutató Qubino ZMNHAA2

Qubino nincs kategorizálva ZMNHAA2

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Qubino ZMNHAA2 (2 oldal) a nincs kategorizálva kategóriában. Ezt az útmutatót 14 ember találta hasznosnak és 7.5 felhasználó értékelte átlagosan 4.7 csillagra

Letöltés PDF

Oldal 1/2

Qubino

The INNOVATIVE SMALLEST and

Flush 1 relay

ORDERING CODE

Z-WAVE FREQUENCY

ZMNHAA2

868,4 MHz

ZMNHAA3

921,4 MHz

ZMNHAA4

908,4 MHz

ZMNHAA5

869,0 MHz

ZMNHAA6

916,0 MHz

This Z-Wave module is used for switching on or

o the electrical device (e.g. light, fan, etc ...). ff

The module can be controlled either through

Z-wave network or through the wall switch.

The module is designed to be mounted inside

a “ ”ﬂush mounting box , hidden behind a

traditional wall switch.

Module measures power consumption of

electrical device and supports connection of

digital temperature sensor. It is designed to act

as repeater in order to improve range and

stability of Z-wave network.

Supported switches

Module supports switches mono-stable

(push button) and switches. The bi-stable

module is factory set to operate with -stable bi

switches.

Installation

 Before the installation disconnect power

supply.

 Connect the module according to

electrical diagram.

 Locate the antenna far from metal

elements (as far as possible).

 Do not shorten the antenna.

Danger of electrocution!

 Module installation requires a great degree

of skill and may be performed only by a

qualiﬁed and licensed electrician.

 Even when the module is turned oﬀ,

voltage may be present on its terminals.

Any works on conﬁguration changes

related to connection mode or load must be

always performed by disconnected power

supply (disable the fuse).

Note!

Do not connect the module to loads exceeding

recommended values. Connect the module

only in accordance to the below diagrams.

Improper connections may be dangerous.

Package conten ts

 Flush 1 relay

Electrical diagram 230VAC

Notes for the diagram:

Electrical diagram 24VDC

Notes for the diagram:

Durability of the module depends on applied

load. For resistive load (light bulbs, etc.) and

10A current consumption of each individual

electrical device, the durability exceeds

100.000 switches of each individual electrical

device.

Module Inclusion (Adding to Z-wave

network)

 Connect module to power supply (with

temperature sensor connected - if

purchased),

 bring module within maximum 1 meter (3

feet) of the main controller,

 enable add/remove mode on main

controller

 auto-inclusion (30 minutes after

connected to power supply) or

 press service button for more than 2 S

second or

 press push button three times within 3I1 s

(3 times change switch state within 3

seconds).

Module Exclusion/Reset (Removing

from Z-Wave network)

 Connect module to power supply

 bring module within maximum 1 meter (3

feet) of the main controller,

 enable add/remove mode on main

controller

 press service button for more than 6 S

second or

 press push button I1 ﬁve times within 3s (5

times change switch state within 3

seconds) in the ﬁrst 60 seconds after the

module is connected to the power supply.

By this function all parameters of the module

are set to default values and own ID is deleted

If service button S is pressed more than 2 and

less than 6 second module is excluded, but

conﬁguration parameters are not set to default

values.

Association

Association enables Flush 1 relay module to

transfer commands inside Z-Wave network

directly (without main controller) to other

Z-Wave modules.

Associated Groups:

Group 1: basic on/oﬀ (triggered at change of

the output Q state and reﬂecting its state) up to

16 nodes.

Group 2: basic on/oﬀ (triggered at change of

the input I2 state and reﬂecting its state) up to

16 nodes.

Group 3: basic on/oﬀ (triggered at change of

the input I3 state and reﬂecting its state) up to

16 nodes.

Group 4: default reporting group (reserved for

the main controller).

Conﬁguration parameters

Parameter no. Input 1 switch type 1 –

Available conﬁguration parameters (data type

is 1 Byte DEC):

 default value 1

 mono-stable switch type (push button) 0

 -stable switch type 1 bi

Parameter no. 2 Input 2 contact type –

Available conﬁguration parameters (data type

is 1 Byte DEC):

 default value 0

 0 NO (normally open) input type

 1 NC (normally close) input type

Parameter no. 3 Input 3 contact type –

Available conﬁguration parameters (data type

is 1 Byte DEC):

 default value 0

 0 NO (normally open) input type

 1 NC (normally close) input type

Parameter no. 10 - Activate / deactivate

functions ALL ON/ALL OFF

Available conﬁguration parameters (data type

is 1 Byte DEC):

 default value 255

 255 - ALL ON active, ALL OFF active

 - ALL ON is not active ALL OFF is not 0

active

 - ALL ON is not active ALL OFF active 1

 - ALL ON active ALL OFF is not active 2

Flush 1 relay module responds to commands

ALL ON / ALL OFF that may be sent by the

main controller or by other controller belonging

to the system.

Parameter no. 11 - Automatic turning oﬀ

relay after set time

Available conﬁguration parameters (data type

is 2 Byte DEC):

 Default value 0

 - Auto OFF disabled 0

 1 65535 = 0,01second 655,35 – –

seconds Auto OFF enabled with deﬁne

time, step is 10mseconds.

Parameter no. 30 - Saving the state of the

relay after a power failure

Available conﬁguration parameters (data type

is 1 Byte DEC):

 default value 0

 Flush 1relay module saves its state 0 –

before power failure (it returns to the last

position saved before a power failure)

 - Flush 1relay module does not save the 1

state after a power failure, it returns to

"oﬀ" position.

Neutral lead

Live lead

Output for electrical device

Input for switch /push button or sensor

Input for switch /push button

Terminal for digital temperature sensor

(only for Flush 1 relay module

compatible digital temperature sensor,

which must be ordered separately).

+ VDC

- VDC

Output for electrical device

Input for switch /push button or sensor

Input for switch /push button

Terminal for digital temperature sensor

(only for Flush 1 relay module

compatible digital temperature sensor,

which must be ordered separately).

Service button (used to

add or remove module

from the Z-Wave

network).

Termékspecifikációk

Márka:	Qubino
Kategória:	nincs kategorizálva
Modell:	ZMNHAA2

Szüksége van segítségre?

Ha segítségre van szüksége Qubino ZMNHAA2, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek

Az Ön neve*

Az Ön e-mail címe*

Írja ide kérdését

Útmutatók nincs kategorizálva Qubino

Qubino Flush RGBW Dimmer Útmutató

30 Augusztus 2024

Qubino ZMNHBA2 power relay Útmutató

25 Augusztus 2024

Qubino ZMNHSD1 Útmutató

25 Augusztus 2024

Qubino Flush 1 Relay Útmutató

25 Augusztus 2024

Qubino ZMNHAA2 Útmutató

25 Augusztus 2024

Qubino Flush 2 Relays Útmutató

25 Augusztus 2024

Qubino Flush 1D Relay Útmutató

25 Augusztus 2024

Útmutatók nincs kategorizálva

Legújabb útmutatók nincs kategorizálva

MOZA SR-P Útmutató

10 Április 2025

Soundstream VRN-64HBL Útmutató

10 Április 2025

Panasonic Lumix DMW-AC11 Útmutató

10 Április 2025

Planet PWR-240-48 Útmutató

9 Április 2025

CaterChef 445001 Útmutató

9 Április 2025

IFM E40581 Útmutató

9 Április 2025

Livn Bolt Útmutató

9 Április 2025

Livn Beats Útmutató

9 Április 2025

Alpine DP2-40C-BC Útmutató

9 Április 2025

IFM O3R252 Útmutató

9 Április 2025