Használati útmutató SEADA G4K Pro
SEADA
processzor
G4K Pro
Olvassa el alább 📖 a magyar nyelvű használati útmutatót SEADA G4K Pro (2 oldal) a processzor kategóriában. Ezt az útmutatót 12 ember találta hasznosnak és 6.5 felhasználó értékelte átlagosan 4.6 csillagra
Oldal 1/2
G4K Pro Quick Start Manual
SD-MA-016 V04
Note
1. Do not fix the device to any surface which is a heat source to avoid over heating
2. Do not cover the surface or ventilation grills of the device to avoid over heating
1. Verify the package contents
Please verify the package contents against the List Below
1. G4K Pro Controller 1
2. Power Adapter 1
3. Ethernet Cable 1
4. Quick Start Guide (SD-MA-016) 1
5. Audio Cable 1
6. Software & Documentation User CD 1
If any of the items in the packing list is missing, please contact your reseller.
2. Set up the G4K Pro
Power up the G4K controller and connect the input and outputs to correct devices.
Figure 1
3. Install the software on control PC
Install the G4K Pro management software from the disk
Users will have the software UI as left.
4. Connect through IP in ‘Device’
The default IP address for G4K Pro controller is
192.168.1.25. Users need to change the IP address of
control PC to the same IP group of G4K Pro.
• Change the ‘Obtain an IP address automatically’
to ‘Use the following IP address’ to set up a static IP address of TCP/IPv4 in Ethernet Properties
➢ IP address: any address between 192.168.1.2 and 192.168.1.254 except the address
which has been taken by the G4K Pro
➢ Subnet mask: 255.255.255.0, Default Gateway: 192.168.1.1
• Once the control PC IP address having been set up, connect PC to either one of RJ45 ports of G4K
Pro controllers via a network cable and then press the Connect button to connect the device.
Model: G4KPro-HDMI
1. Lockable Power Supply
2. Reset Button
• Back to Factory Settings
• Press+hold for 3 seconds
3. RJ45 Ethernet Ports
4. HDMI Input Port
5. Status Lights
6. Audio Output Port
7. HDMI Output Ports
8. Daisy Chain HDMI Ports
• To Other G4K Pro Units
9. Screw holes for Lockable
HDMI cables
• Please take the cover screws
out before use
A
Figure 1
1 2 3 4 5
6 7 8
9
9
Figure 2
G4K Pro Quick Start Manual
SD-MA-016 V04
5. Set up video wall layout in ‘Output’
• Once the unit is connected, press ‘Output’ to set up the layout.
• Type in the Dotpitch and bezel sizes (check display datasheet) in ‘output’.
➢ Dot Pitch: Display area Length (L) ÷ Quantity of Horizontal pixel (e.g.
1920)
For example
➢ 46’’ screen has 0.531mm Dot Pitch
➢ 49’’ screen has 0.561mm Dot Pitch
➢ 55’’ screen has 0.631mm Dot Pitch
• And then press ‘Apply To All Monitors’ to apply the changes to all screens
• Press ‘Apply To Single Monitor’ to apply the changes only to the current
highlighted screen
• Move/rotate the screens in software to create the desired layout
• Enter any degree in ‘Angle’ and then press ‘Rotate All Monitors’ (A)
• Enter any degree in ‘Angle’ and then press ‘Rotate’ for single screen (B)
• Press ‘Apply’ to enable any layout change
Note: no change will be applied to the video wall until ‘Apply’ button has been pressed (C)
6. Set up input video window in ‘Input’
• Once the video wall layout having been set up,
press ‘Input’ to set up the input video window
• Users are able to move/resize the input video
window onto the video wall
• Users are able to open/close the input video
window via pressing the button of ‘Open Window’ and
‘Close Window’ respectively.
• Users are able to open multi video input windows
when multi G4Ks are connected
➢ Highlight the G4K device whose input window
needed to be opened
➢ And then press the ‘Open Window’ button to
open the window
➢ Each input window will have a unique window ID
• There are 3 modes for opening input source window
➢ Lock Aspect Ratio Window covers the screen with the same aspect ratio as input source
➢ Frame Window covers the video wall to the edge of frames of the screens
➢ None Window covers the video wall to the display edge of the screens
7. Create Pre-set layout for G4K Pro
There are two ways to create and save pre-set layouts for future recall.
• One way is to save up to 4 layouts onto the device so that the layouts can be loaded by G4KPro
management software, iGPro from Apple App Store or 3rd party controller via telnet (Figure 4-A).
• Another method is to use Save & Load buttons on toolbar to save unlimited layouts onto
control PC and load them using G4KPro management software. There are a few sample layouts already
in the folder for users to use.
This quick start guide provides basic instructions for setting up SEADA G4K Pro video wall controllers. For
additional information (e.g. daisy chain) about how to use the controllers, please refer to the G4K Pro User
Guide (SD-MA-017), which is available on the CD included in this package.
Figure 3
Figure 4
Figure 4
A
A
B
C
Termékspecifikációk
| Márka: | SEADA |
| Kategória: | processzor |
| Modell: | G4K Pro |
Szüksége van segítségre?
Ha segítségre van szüksége SEADA G4K Pro, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek
Útmutatók processzor SEADA
30 Augusztus 2024
30 Augusztus 2024
30 Augusztus 2024
30 Augusztus 2024
30 Augusztus 2024
30 Augusztus 2024
30 Augusztus 2024
30 Augusztus 2024
30 Augusztus 2024
30 Augusztus 2024
Útmutatók processzor
- processzor Alpine
- processzor Atlas Sound
- processzor AudioThing
- processzor Solid State Logic
- processzor Neutrik
- processzor AMX
- processzor Fredenstein
- processzor Intel
- processzor Phoenix Gold
- processzor Dangerous Music
- processzor DataVideo
- processzor Asus
- processzor Golden Age Project
- processzor Rupert Neve Designs
- processzor Radial Engineering
Legújabb útmutatók processzor
3 Április 2025
19 Március 2025
16 Január 2025
16 Január 2025
16 Január 2025
16 Január 2025
16 Január 2025
16 Január 2025
16 Január 2025
16 Január 2025