Használati útmutató AMX MXA-STMK-10

AMX nincs kategorizálva MXA-STMK-10

Olvassa el alább 📖 a magyar nyelvű használati útmutatót AMX MXA-STMK-10 (2 oldal) a nincs kategorizálva kategóriában. Ezt az útmutatót 10 ember találta hasznosnak és 5.5 felhasználó értékelte átlagosan 4.6 csillagra

Letöltés PDF

Oldal 1/2

QUICK START GUIDE

MXA-STMK-10 Secure Table Mount Kit

MXA-STMK-10

The MXA-STMK-10 Secure Table Mount Kit (FG5968-66) is a beautifully styled plate

that, when attached to the Modero X Series® 10.1” Tabletop Touch Panel and secured

with the under-table tamper resistant bolts, will make it virtually theft proof. If drilling

into the table is not feasible, the secure mounting plate can be attached to the touch

panel (but not the table) and then secured with a Kensington® Lock.

Use both methods simultaneously for extra security. The MXA-STMK-10 is compatible

with all Modero X Series 10.1” Tabletop Touch Panels, including the MXT-1001

(FG5968-47), MXT-1000 (FG5968-03) and MXT-1000-NC (FG5968-24).

Installation

The MXA-STMK-10 may be mounted in one of two ways: it can be affixed to a table or

other surface using the included hex head bolts and tamper-proof nuts, or it can be

allowed to move freely but constrained by a Kensington Lock cable. For additional

security, both options may be used at the same time.

NOTE: For the table mount installation, the tools necessary include a drill with a 1/4” bit,

a Phillips head screwdriver, and an adjustable-head box wrench. The Kensington Lock

installation requires use of a Phillips head screwdriver.

Table Mount Installation

To install the MXA-STMK-10 to a table or other surface:

1. Place the security mount base in the location where it is to be installed, taking

care not to put the mount base past the edge of the table.

2. Mark the location of the hex head bolt holes going through the security mount

base, such as by drilling through the holes into the table (FIG. 2).

When drilling through the holes, use a 1/4” or 5/16” drill bit to allow the bolts to

pass through during installation.

Clean out the drilling debris from the holes and from the surface of the table.

3. On the touch panel, turn the touch panel upside down and remove the 2 Phillips

head screws at each corner from the bottom of the device (FIG. 3).

The screws to be removed are next to the rubber feet on the front end.

Store these screws in a secure location in case you wish to uninstall the secure

table mount plate.

4. Install the hex head bolts through the security mount base.

Do NOT secure the bolts in the table at this time.

5. Using the two Phillips flat head screws included in the kit, secure the security

mount base to the bottom of the touch panel from the underside of the base

(FIG. 4).

These holes must align with the holes in the touch panel’s base from which the

screws were already removed (FIG. 3).

6. Pass the hex head bolts through the table.

FIG. 1

MXA-STMK-10 SECURE TABLE MOUNT KIT

PRODUCT SPECIFICATIONS

Dimensions (HWD): 0.49” x 9.92” x 5.88” (1.25 cm x 25.20 cm x 12.42 cm)

Weight: 1.90 lbs (0.86 kg)

Included Accessories: • Security Mount Base (62-5968-52)

• Kensington Lock Bracket (62-5968-50)

• Screw, 8-32 X .1.00, Torx Flat Head, Black (2) (80-5005)

• Screw, 6-32 X .375, Phillips Flat Head, Black (2) (80-5006)

• Nut, 1/4-20, Tamper Proof (3) (80-5007)

• Washer, 1.5 Dia X .312 Thick , Nylon (2) (80-5008)

• Bolt, 1/4-20 X 3.00 Hex Head, Black (2) (80-5009)

• Round Dip-Molded End Cap, Black (2) (80-5010)

• MXA-STMK-10 Quick Start Guide (93-5968-66)

Other AMX Equipment: • MXT-1000 10.1" Modero X Series Tabletop Touch Panel

(FG5968-03)

• )MXT-1001 10.1" Modero X Series G5 Tabletop Touch Panel

(FG5968-47)

• MXT-1000-NC 10.1" Modero X Series Tabletop Touch Panel (no

Camera, no Microphone) (FG5968-21)

For more information on the MXT-1000 10.1" Modero X Series Tabletop Touch Panel, refer

to the MSD/T-1000 Operation Reference Guide (available to view/download at

www.amx.com).

Kensington

Lock Bracket

5.88”

(12.42 cm)

9.92”

(25.20 cm)

Top

Front

0.49”

(1.25 cm)

Hex Head

Bolt Holes

FIG. 2 MARKING THE LOCATION OF THE HEX HEAD BOLT HOLES

FIG. 3 LOCATION OF THE PHILLIPS HEAD SCREWS ON THE BOTTOM OF THE TOUCH PANEL

FIG. 4 SECURING THE SECURITY MOUNT BASE TO THE BOTTOM OF THE TOUCH PANEL

Phillips head screw

Termékspecifikációk

Márka:	AMX
Kategória:	nincs kategorizálva
Modell:	MXA-STMK-10
Termék színe:	Fekete
Kompatibilitás:	MXT-1001 (FG5968-47), MXT-1000 (FG5968-03), MXT-1000-NC (FG5968-24)
A támogatott kijelzők száma:	1
Felszerelés típusa:	Asztali