Használati útmutató NEC PDVW MFS 46 55 P
NEC
Lapos panel támogatás
PDVW MFS 46 55 P
Olvassa el alább 📖 a magyar nyelvű használati útmutatót NEC PDVW MFS 46 55 P (28 oldal) a Lapos panel támogatás kategóriában. Ezt az útmutatót 3 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.9 csillagra
Oldal 1/28
I N S T A L L A T I O N I N S T R U C T I O N S
Instrucciones de instalación
Installationsanleitung
Instruções de Instalação
Istruzioni di installazione
Installatie-instructies
Instructions d´installation
MSMVPU LSMVPU
FUSION MEDIUM AND LARGE PULL-OUT
PORTRAIT FLAT PANEL MOUNTS
MSMVPU/LSMVPU Installation Instructions
2
DISCLAIMER
Milestone AV Technologies, and its affiliated corporations and
subsidiaries (collectively "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
IMPORTANT WARNINGS AND
CAUTIONS!
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component. The wall to which the mount is being attached
may have a maximum drywall thickness of 5/8" (1.6cm).
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components located on the MSMVPU does not exceed
125 lbs (56.7 kg) or 150 lbs (68 kg) for the LSMVPU.
Installation Instructions MSMVPU/LSMVPU
3
DIMENSIONS
20.57
522.5
18.79
477.4
1.58
40.1
15.10
383.4
13.53
343.7
7.63
193.7
1.75
44.5
1.00
25.4
.33
8.3
3.93
99.7
16.00
406.4
1.40
35.5
NOTCH CUTOUTS ARE
VERTICAL C/L OF MOUNT
24.44
620.7
16.53
419.9
7.00
177.8
3.72
94.5
12X
.34
8.6
.41
10.4
12X
1.06
27
0
0
.45
11.5
1.97
50
2.42
61.5
3.94
100
4.39
111.5
5.91
150
6.36
161.5
7.87
200
8.33
211.5
9.84
250
10.30
261.5
11.81
NOTES:
MAXIMUM MOUNTING PATTERN WIDTH IS 16.44"[410mm].
1.
MINIMUM MOUNTING PATTERN WIDTH IS 3.94"[100mm].2.
MOUNT IS 3.72"[94.5mm] DEEP WHEN FLAT TO WALL.3.
EXTENSION DISTANCE IS 7.0"[177.8mm] WITH A MAXIMUM EXTENSION FROM WALL OF 10.7"[272mm
FOR RECESSED APPLICATIONS, MINIMUM VERTICAL LIFT FOR HOOK ENGAGEMENT IS .56"[14.2mm].
MSMVPU
MEASUREMENTS: [MILLIMETERS]
INCHES
LSMVPU
MEASUREMENTS: [MILLIMETERS]
INCHES
20.57
522.5
15.10
383.4
6.00
152.4
1.00
25.4
.33
8.3
3.55
90.1
2.92
74.1
1.75
44.5
1.00
25.4
3.93
99.7
NOTCH CUTOUT SIGNIFY
VERTICAL C/L OF MOUNT
RAILS CAN BE SLID LEFT OR
RIGHT FOR OFFSET
MINIMUM VERTICAL
SPACING IS 12"[305mm]
DIAMOND CUTOUT ALIGNS WITH
VERTICAL C/L OF MOUNT
3.71
94.3
32.50
825.5
16.52
419.6
.38
9.6
.49 TYP
12.5
31.75
806.4
.13
3.2
8X 1.60
40.7
.34
TYP
8.6
MAXIMUM MOUNTING PATTERN WIDTH IS 16.43"[410mm].
1.
MINIMUM MOUNTING PATTERN WIDTH IS 3.94"[100mm].
2.
MOUNT IS 3.71"[94.3mm] DEEP WHEN FLAT TO WALL.3.
EXTENSION DISTANCE IS 7.0"[177.8mm] WITH A MAXIMUM EXTENSION FROM WALL OF 10.7"[272mm].
FOR RECESSED APPLICATIONS, MINIMUM VERTICAL LIFT FOR HOOK ENGAGEMENT IS .56"[14.2mm].
Termékspecifikációk
| Márka: | NEC |
| Kategória: | Lapos panel támogatás |
| Modell: | PDVW MFS 46 55 P |
Szüksége van segítségre?
Ha segítségre van szüksége NEC PDVW MFS 46 55 P, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek
Útmutatók Lapos panel támogatás NEC
15 Október 2024
2 Október 2024
16 Szeptember 2024
15 Szeptember 2024
6 Augusztus 2024
1 Augusztus 2024
1 Augusztus 2024
28 Július 2024
28 Július 2024
26 Július 2024
Útmutatók Lapos panel támogatás
- Lapos panel támogatás Iiyama
- Lapos panel támogatás SmartMetals
- Lapos panel támogatás Amer
- Lapos panel támogatás Zaor
- Lapos panel támogatás HP
- Lapos panel támogatás ViewZ
- Lapos panel támogatás Ewent
- Lapos panel támogatás Bell'O
- Lapos panel támogatás Nabo
- Lapos panel támogatás NeoMounts
- Lapos panel támogatás 3M
- Lapos panel támogatás Panduit
- Lapos panel támogatás Reflecta
- Lapos panel támogatás My Wall
- Lapos panel támogatás Unicol
Legújabb útmutatók Lapos panel támogatás
8 Április 2025
3 Április 2025
3 Április 2025
3 Április 2025
3 Április 2025
3 Április 2025
3 Április 2025
3 Április 2025
3 Április 2025