Használati útmutató Schneider WDE002939
Schneider
Termosztát
WDE002939
Olvassa el alább 📖 a magyar nyelvű használati útmutatót Schneider WDE002939 (46 oldal) a Termosztát kategóriában. Ezt az útmutatót 5 ember találta hasznosnak és 3 felhasználó értékelte átlagosan 4.2 csillagra
Oldal 1/46
© 2011 Schneider Electric 1
Multi-function application with RTR and FanCoil 1816/1.0
Function overview
This application provides you with the following func-
tions:
• Temperature control with various display options
• Scene function
• Disable function for push-buttons
• Time control
• Valve control
• Push-button functions
All buttons can be assigned different functions inde-
pendently. You can do the following:
• Switch and toggle
• Dim
• Control blinds
• Save and retrieve scenes
• Select a linear regulator function
• Save edge functions
• Adjust setpoints
• Access operation modes and toggle between them
The status LEDs can also be utilised independently of
one another and in a wide variety of ways.
Group addresses
Group addresses are managed dynamically. Maximum
number of group addresses and assignments: 254 ad-
dresses, 255 connections
Notes on this documentation
This application enables you to implement a multitude
of functions with the push-button. However, which func-
tions are possible in each individual case depends on
the KNX devices being controlled (e.g. dimming actua-
tors, switch actuators etc.). The functions described
here therefore show only the settings for this push-but-
ton.
|Many parameters and their settings are depend-
ent on the settings you have already made for oth-
er parameters. This means that some parameters
will appear or disappear and the values available
for selection will change according to settings you
have already made. These dependencies have
not been shown in the table for reasons of clarity.
All settings are always shown.
|Configurable times (staircase timer, ON delay,
OFF delay, cyclic intervals etc.) are set via the
base and factor parameters. The actual time is giv-
en by the multiplication of the two values. Exam-
ple: Base = 1 second * factor = 3 gives 3 seconds.
|The bold values in a table are the values set dur-
ing factory configuration.
Before you begin, make a few basic settings in the
"General" tab. You can specify the following:
• Whether the operational LED switches off or displays
that the device is operating.
• How the date and time are received.
• Whether and how the time is sent cyclically to the bus.
• How large the start-up delay for the device should be
after bus voltage recovery.
General settings for date and time
Here you set whether the date and time are received by
two communication objects (3 byte each) or by only one
communication object. In the latter case, there is an 8
byte object available.
If you send the time cyclically to the bus, you either have
an output object with 3 byte or one with 8 byte, depend-
ing on which format you selected.
You can find more details on time control, synchronisa-
tion and master-slave functions in the "Time control"
chapter.
Start-up delay
The start-up delay is the time delay between the bus
voltage recovery and the device's functional start. Set a
time after which the current values can be read by other
KNX devices.
Communication objects
You can select the following communication objects:
Multi-function application with RTR and
FanCoil 1816/1.0
Basic settings
General
Parameter Settings
Switch on operational LED Yes
No
Receive date and time In one communication object
In two communication objects
Send time cyclically No
Every minute
Every hour
Daily
Format of sent time Date/time format (8 byte)
Time format (3 byte)
Device's start-up delay in s (0-255) 2-255, 4
Function Object name Type Prio Flags Behaviour
Time control Date object input 3 byte Low WC Receive
Time control Time object input 3 byte Low WC Receive
Time control Date/time object
input
8 byte Low WC Receive
Time control Date/time object
output
8 byte Low CT Transmit
Time control Time object out-
put
3 byte Low CT Transmit
Termékspecifikációk
| Márka: | Schneider |
| Kategória: | Termosztát |
| Modell: | WDE002939 |
Szüksége van segítségre?
Ha segítségre van szüksége Schneider WDE002939, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek
Útmutatók Termosztát Schneider
27 Szeptember 2024
8 Augusztus 2024
3 Augusztus 2024
2 Augusztus 2024
21 Július 2024
13 Július 2024
12 Július 2024
11 Július 2024
Útmutatók Termosztát
- Termosztát Max
- Termosztát VDH
- Termosztát Xavax
- Termosztát Energenie
- Termosztát Buderus
- Termosztát Emerson
- Termosztát Muller
- Termosztát Nobo
- Termosztát Hoffman
- Termosztát Emko
- Termosztát ICY
- Termosztát Nexa
- Termosztát Hugo Muller
- Termosztát Crestron
- Termosztát Cotech
Legújabb útmutatók Termosztát
9 Április 2025
7 Április 2025
7 Április 2025
6 Április 2025
6 Április 2025
6 Április 2025
5 Április 2025
4 Április 2025
4 Április 2025
3 Április 2025