Használati útmutató Vemer Energy-230 Wi-Fi
Vemer
Mérőberendezések
Energy-230 Wi-Fi
Olvassa el alább 📖 a magyar nyelvű használati útmutatót Vemer Energy-230 Wi-Fi (2 oldal) a Mérőberendezések kategóriában. Ezt az útmutatót 16 ember találta hasznosnak és 8.5 felhasználó értékelte átlagosan 5.0 csillagra
Oldal 1/2
03-2024
REFERENCE STANDARDS
EU CONFORMITY DECLARATION
Vemer declares that the device complies with the Communitary Directive 2014/53/EU
(RED) with reference to the following standards:
• EN 61010-1 • EN 50470-1 • EN 50470-3 • EN 300 328 • EN 301 489-1
• EN 301 489-17
The full text of the EU Conformity Declaration is available at www.vemer.it address.
V3IS01181-010
Mod. Energy-230 Wi-Fi
Manuals
download
PDF
2
INSTRUMENT DESCRIPTION and DIMENSIONS
User Manual
SINGLE-PHASE ACTIVE ENERGY METER WITH WI-FI MODULE
Read all the instructions carefully
Energy meter from DIN bar designed to measure the consumption of active energy into
the grid in single-phase systems. The current insertion is direct for values up to 40A.
The integrated Wi-Fi module is used to manage the device remotely using your smartphone
or tablet. You need to connect the device to your home router and install the dedicated App
on your smartphone or tablet, available free of charge for Android and iOS devices.
On the application it is possible to view the measurements of total energy, partial
energy and instantaneous power. It has a pulse output for remote energy counting.
Energy-230 Wi-Fi is an electronic device intended to operate in environments with overvoltage
category III and pollution degree 2 according to the EN 61010-1 standard.
Code Model Description
VE794600 Energy-230 Wi-Fi
Single-phase active energy meter with Wi-Fi interface
SAFETY WARNINGS
During product installation and operation it is necessary to observe the following
instructions:
1) The product must be installed by a qualified person, strictly in observance of the
connection diagrams shown in this manual.
2) The product must be installed and activated in compliance with current electric
systems standards
3) After installation inaccessibility to the terminals without using dedicated tools
must be guaranteed
4) Do not use the product for anything other than the indicated purpose.
5) The product must be installed in an adequately protected closed electrical panel.
6) In the supply network there must be a bipolar disconnection.
7) In the electrical system upstream of the product must be installed a protection
device against the overcurrents.
8) Before accessing the connection terminals, make sure that the leads are not live.
9) Do not connect or feed the product if any part of it is damaged.
10) The product can be used in environments with Measurement Category III
and Pollution degree 2, according to the Standard EN 61010-1.
TECHNICAL SPECIFICATIONS
• Power supply: 230 Vac (-15% ÷ 10%) 50/60 Hz
• Absorption: 4.7 VA (1.5 W)
• Starting current: Ist = 20 mA
• Minimum current: Imin = 0.25 A
• Reference current: Iref = 5 A
• Maximum current: Imax = 40 A
• Insertion type: direct
• Pulse output for remote reading of the collected energy count:
- 200 imp/kWh
- Pulse duration 100 ms ±15%
- Pulse voltage 9 ÷ 24 VDC ± 10%
- Switchable output current 20 mA Max
• Cable terminal block with a maximum section of 6 mm
2
• Communication interface: Wi-Fi and Bluetooth BLE 5.0
• Operating frequency band:
- Wi-Fi: 2.4 GHz IEEE 802.11 b/g/n
- Bluetooth: 2400-2483.5 MHz
• Maximum transmitted radiofrequency power:
- Wi-Fi: 18.3 dBm
- Bluetooth: 4 dBm
• LED: 3 operation status signal LEDs
• Precision: Class B
• Keypad: 1 key for configuration
• Operating temperature: -10°C ÷ 45°C
• Operating humidity: 20 ÷ 90% non-condensing
• Storage temperature: -25°C ÷ 70°C
• Insulation: reinforced between accessible parts (front) and all the other clamps
• Container: 2 DIN modules
• Degree of protection: IP20/IP51 on the front
• Create a Vemer account:
1. Install and launch the Energy Wi-Fi App on your
smartphone (or tablet)
2. Choose "REGISTER NOW" and fill in the "e-mail" and
"password" fields
Note: for security reasons, it is advisable to choose a
password different from the one used to access your
e-mail inbox
3. Check your e-mail address: confirm account activation
by clicking on the link contained in the e-mail sent by the
system
4. Log in by entering the e-mails and passwords chosen
during registration
To configure the device using a smartphone
proceed as follows:
1. Verify that the phone you are using is connected
to the home Wi-Fi network where the device
will be connected.
2. Launch the App and press the "+" button on
the Home page.
3. On the Energy Wi-Fi, hold down the SET key
until the yellow LED ( ) starts to flash quickly
to activate configuration mode. Now wait for the
yellow LED (
) to start flashing slowly before
proceeding.
4. On the App:
a. follow the instructions in the wizard and press
"Next".
b. find and select in the list the device "EW_..."
to connect to the Energy Wi-Fi (the yellow
LED (
) will come on fixed to indicate the
connection between the App and the device).
c. now enter the full name (SSID) and password of the Wi-Fi network to which the
device is connected, being sure to faithfully type in all the component characters
(upper-case, lower-case, spaces, digits).
Press Continue to proceed.
5. On the App enter a name that helps identify the Energy Wi-Fi and confirm
by pressing the Save
6. On the Energy Wi-Fi , check that the green LED (
) starts flashing and after
a short while becomes fixed to indicate correct connection with the home network.
The configuration procedure has ended. At this point:
the App displays the list of devices associated with your account which must also
include the newly associated device
on theEnergy Wi-Fi the green LED (
) will be on fixed
7
LED SIGNALS
The 3 LEDs on the device, based on the types of ignition described in the table, help to understand the operating status of the device:
LED
Ignition type Operating status
GREEN ( )
Fixed on Normal operation
Slow ashing Attempting to connect to the Wi-Fi network (during the remote control con guration phase)
Single ashing Incorrect Wi-Fi password entered
Double ashing No Wi-Fi connection or incorrect Wi-Fi network name entered
Triple ashing Generic Wi-Fi connection error
Quadruple ashing No Internet connection
Short shutdown Time absence
YELLOW ( )
Fixed on
Power produced (during normal operation of the device)
Fixed on Connection with smartphone successful (during the remote control con guration phase)
Fast ashing Preparation of BLE mode for remote control con guration
Slow ashing BLE mode active for remote control con guration
RED ( )
Flashing Energy absorbed (each ash indicates an increase in the energy meter of 10 Wh)
GREEN ( ) + YELLOW ( )
Simultaneous short ignition No network con guration
Simultaneous xed access Starting and/or resetting of the device
Simultaneous fast ashing Keypad lock enabled (displayed when the key is pressed)
Alternate Device identi cation (displayed with application command)
GREEN ( ) + YELLOW ( ) + RED ( )
Simultaneous slow ashing Internal memory error
1
(Max 40 A)
User / Load
Pulse output
5 Wh/Imp
3
CONNECTION DIAGRAM
5
PRELIMINARY OPERATIONS
6
CONFIGURATION REMOTE CONTROL
WARNINGS
Use of the energy meter via the Energy Wi-Fi App must be performed
in the presence of a 2.4 GHz Wi-Fi network connected to the Internet.
The smartphone used for configuration must be connected to the same Wi-Fi network.
Make sure you have a Vemer account.
Also ensure that the distance from the router is such as
to ensure stable communication.
4
WARNINGS FOR THE CORRECT POSITIONING AND
CONNECTION OF THE DEVICE TO A WI-FI NETWORK
For the correct operation and use of the device through the remote control via the App,
carefully follow the points below:
• Install and connect the device according to the connection diagrams in this manual.
• Check that:
1. the Router and/or the Wi-Fi Access Point are correctly switched on and at a distance
such as to guarantee a stable communication signal with the device
2. the Router has full access to the Internet and there are no browsing restrictions
(firewall settings, parental control,...)
3. The 2.4 GHz frequency band is also enabled in the Router settings (if the Router
only supports the 5 GHz frequency range, it will not be possible to operate the device;
for further information see the user instructions of your Router)
4. the smartphone used for configuration is connected to the same Wi-Fi network to which
the device is connected
5. position detection (GPS) of your smartphone is active and the consent to the
Energy Wi-Fi App to be able to identify the position (GPS) of the device is enabled
(adapt the settings on the smartphone such as to be able to perform this tracking;
for further information see the instructions of your
smartphone)
E-mail
Login
Password
Forgotten password?
Or login with:
REGISTER NOW
No devices
currently configured.
Set up a new device
The key on the device, depending on the type of pressure exerted, is used to perform the operations described in the table:
KEY
Pressure type Function
SET
Prolonged pressure (> 3 sec) Enabling of BLE mode for remote control con guration
Short pressure Forcing of communication with the server
Short pressure
(during the remote control con guration phase)
BLE mode output for remote control con guration
Prolonged pressure (> 5 sec)
(during the remote control con guration phase)
Reset settings: reset of all settings to factory values and deletion of account association
8
KEYBOARD OPERATION
Vemer S.p.A.
I - 32032 Feltre (BL) • Via Camp Lonc, 16
e-mail: info@vemer.it - web site: www.vemer.it
1 Green LED: Wi-Fi network connection
status
2 SET key: con guration activation/
deactivation
3 Clamps for pulse output
4 Yellow LED: Wi-Fi con guration/
pairing or power output
5 Red LED: absorbed energy signal
( ashing with a frequency of 10Wh)
6 Clamps for direct insertion of
measuring conductors
1
2
5
6
4
3
information to users pursuant to art. 14 of the directive
2012/19 / EU of the european parliament and of the council
of 4 july 2012 on waste electrical and electronic equipment (WEEE)
If the crossed-out bin symbol appears on the equipment or packaging,
this means the product must not be included with other general waste
at the end of its working life.
The user must take the worn product to a sorted waste center,
or return it to the retailer when purchasing a new one.
Products for disposal can be consigned free of charge (without any new purchase obligation)
to retailers with a sales area of at least 400 m
2
, if they measure less than 25 cm.
An efficient sorted waste collection for the environmentally friendly disposal of the used device, or its
subsequent recycling, helps avoid the potential negative effects on the environment and people’s health,
and encourages the re-use and/or recycling of the construction materials.
Termékspecifikációk
| Márka: | Vemer |
| Kategória: | Mérőberendezések |
| Modell: | Energy-230 Wi-Fi |
Szüksége van segítségre?
Ha segítségre van szüksége Vemer Energy-230 Wi-Fi, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek
Útmutatók Mérőberendezések Vemer
2 Október 2024
31 Augusztus 2024
5 Augusztus 2024
28 Július 2024
25 Július 2024
25 Július 2024
20 Július 2024
20 Július 2024
17 Július 2024
13 Július 2024
Útmutatók Mérőberendezések
- Mérőberendezések J.P. Instruments
- Mérőberendezések Güde
- Mérőberendezések Beurer
- Mérőberendezések Sonel
- Mérőberendezések Atmel
- Mérőberendezések IFM
- Mérőberendezések MSW
- Mérőberendezések Fantini Cosmi
- Mérőberendezések Elgato
- Mérőberendezések Laserliner
- Mérőberendezések Seaward
- Mérőberendezések Topex
- Mérőberendezések Hikmicro
- Mérőberendezések Ade
- Mérőberendezések Grundfos
Legújabb útmutatók Mérőberendezések
3 Április 2025
3 Április 2025
3 Április 2025
3 Április 2025
3 Április 2025
3 Április 2025
3 Április 2025
3 Április 2025
3 Április 2025
3 Április 2025