Használati útmutató Vemer Energy-400 D PWRi

Vemer Mérőberendezések Energy-400 D PWRi

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Vemer Energy-400 D PWRi (1 oldal) a Mérőberendezések kategóriában. Ezt az útmutatót 4 ember találta hasznosnak és 2.5 felhasználó értékelte átlagosan 4.3 csillagra

Letöltés PDF
Oldal 1/1
Mod. Energy-400 D PWRi
Energy-400 D PWRi
V3IS00418-011
Vemer S.p.A.
I - 32032 Feltre (BL) • Via Camp Lonc, 16
Tel +39 0439 80638 • Fax +39 0439 80619
e-mail: info@vemer.it - web site: www.vemer.it
65
87
45
60
72
L3
L2
L1
N
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
PWR/PWRi PWRi
PWRi P1 P2
S1 S2
S1 S2
I
I
L3
L2
L1
+
L3
L1
L2L3
N
L1
L2
+
PWR P1 P2
User Manual
THREE-PHASE ACTIVE ENERGY METER
Read all the instructions carefully
 Seriesof4-DINsizestaticmeterstoreadactiveenergyconsumptionin400Vthree-phase
systems
 –ENERGY-400DPWRwithcurrentinletthroughshunt
 –ENERGY-400DPWRiwithcurrentinletthrough
coils
,withgalvanicisolationbetweenthe
primaryandthesecondary
 Connectiontothepowersourceisthroughexternal
ATs
typex/5A
SAFETY WARNINGS
To guarantee correct installation, observe the following instructions:
1) The appliance must be installed by a qualified operator
2) The appliance must be installed in an electrical panel which, after installation,
leaves terminals inaccessible
3) A protection device against over-currents must be installed in the electrical system
upstream of the energy meter
4) Connect the instruments as shown in the diagrams opposite
5) Before making contact with terminals, ensure that conductors to be connected to
the appliance are not live
6) Do not power or connect the appliance if any part of it is damaged
Code Model Description
VE119400 Energy-400 D PWR Three-phaseactiveenergymeter
VE120200 Energy-400 D PWRi Insulatedthree-phaseactiveenergymeter
TECHNICAL SPECIFICATIONS
• Powersupply:3x230(400)VAC(-15%÷+10%),50/60Hz
• InputCurrent:In = 5A; Imax=6A
• Startupcurrent:≤15mA
• Maximumconsumption:3,5VAto400VAC
• Accuracy:class2(EN62053-21)
• Maximumloss: voltagecircuits<2.5VA
  powercircuits<2.5VA
• Galvanicisolationbetweenthevoltageinputsandthecurrentinputs(formodel
PWRi only
).
• AmperometricconnectionbyexternalATx/5A
• Display:bywayof7+5digitLCDdisplayunits
• Partialenergyresolution:xed1kWh
• Totalenergyresolution:xed1kWh
• Pulseproperties:Length:100ms±15%
  Voltage:9÷24VCC±10%
  Maximumoutputcurrent:20mA
• Signalingleds:green=poweron
  red=ashingat1/4kWh
  yellow=wrongconnection
• Optoinsulatedpulseoutputforremotemeterreading
• Operatingconditions:Temperature:-10÷+45°C
  Relativehumidity:10%÷90%noncondensing
• Storagetemperature:-25°C÷+70°C
• Enclosure:4DINsizes
• IngressprotectionratingIP:IP20/IP51onthefront
INSTALLATION
1) Onpoweringthedeviceup,selectthetransformationratioaccordingtotheexternalATx/5A
used.TheATsecondariesofthesolePWRimodelcanbeconnectedtotheearthingsystem
2) Thedevicemustbeconnectedasinthediagram,observingATenergydirection
3) Inorderfortheerrortostaywithinthedevice’sclasslimitsitisnecessarytousethecurrent
transformer in its linear operating range
PROGRAMMING EXTERNAL ATS (X/5A)
 SwitchthedeviceonwhileholdingdownthePRGkeyuntilthe
rmwareversionpageappears.
 PressthePRGkeytoaccessthepagereadingthedevice’sserialnumber
andthentheATsettingpage.
 TherstvaluedisplayedistheATprimary,accordingtothesettingsassignedtothedevice
untilthen.TosettheATvalue,selectthedigitthatneedstobechangedusingthePRGkey.
Whenthedigitselectedashes,changeitusingthearrowkeys and .Therangeof
availablevaluesisfrom0005to1000.ToexittheprogrammingmodeholdthePRGkeydown
foratleast3seconds.IfwhileintheATsettingwindow,nokeyispressedfor30seconds,this
willbeexitedandnochangewillbestored.
 Thedefaultfactorysettingis5/5A.
Note: When the AT setting is altered, then the partial energy meter is zeroed, whereas
the total energy meter remains unchanged.
OPERATION
• Whenthedeviceisturnedonthemainpageisdisplayed,representing
thetotalenergycountonthe7-digitupperblockandthepartialenergy
countonthe5-digitlowerblockThemeasuringresolutionforboth
metersis1kWh
• Todisplaythe
total
energycountonly,pressthe key:thismeter
cannot be set to zero
• Todisplaythe
partial
energyreading,pressthe keyagain:this
metercanalsobezeroedmanuallyanytimebyholdingthe“Prg”key
pressedformorethanfourseconds
• Toreturntothemainpagereadingbothmeters(totalandpartial
energy),pressthe keyagain
Pressthe keytoreverttheabovedescribedsequence.i.e.scrollthe
pagesbackward.
Note: The energy value reading refers to the complete three-phase system as an
algebraic addition (Etot
= E1
+E2+E3)
BACKLIGHTING
 Backlightingisenabledbydefault:itisswitchedoneachtimethekey
ispressedandstaysonfor30secondsafterthelastkeyispressed.In
ordertoenable/disablethebacklighting,gothe
main page
andhold
the“Prg”keypressedforatleast4seconds:theON/OFFbacklight
statuswillbedisplayedforacoupleofseconds,afterwhichthemain
pagewillreturn.
CONNECTION CHECKS
 Whenthedeviceisswitchedon,correctconnectiontocurrentand
voltageterminalsarechecked.Ifconnectionisincorrect,theyellow
LEDlightsupforthreeminutesandthengoesoff.
 Atthisstageandduringnormaloperationitispossibletoviewthe
detailedconnectionstatusbyholdingdownthePRGpush-buttonfrom
thetotalmeterpage:theATsettingpage(read-onlyatthisstage)and
theconnectionstatuspagewillthenbedisplayedsuccessively,withthe
possibleerrors(ifany).
 Incaseoferrorthefollowingmessagesmayappearonthedisplay:
 Connectionerrorononephase(L1inthiscase)
E1 is negative
 Connectionerrorontwophases(L1andL2inthiscase)
 E1andE2arenegative
 Connectionerroronthreephases
 E1,E2andE3arenegative
 Toexittheerrorreadingpage,pressthePRGkey.
 Ifnoerroristobereportedthe“noError“messagewillbereadfora
coupleofseconds.Thenthedevicewillresumenormaloperationfrom
thetotalenergypage.
Note: to restore correct meter operation after an error reading has been displayed,
switch the meter off, connect voltage and current as in the diagrams and then switch
the meter back on.
STANDARD REFERENCES
ConformitytotheEUdirectives:
2006/95/EC
(LowVoltage)
89/336/EEC
modiedby
92/31/EEC
and
93/68/EEC
(E.M.C.)
isdeclaredwithreferencetothefollowingharmonisedstandards:
Safety:
EN61010-1
Electromagnetic compatibility:
EN62052-11andEN62053-21
Dimensions
Connection diagram
Description
ON
PRG
Energy-400 D PWRi
3x230/400V~ 50/60 Hz
In/5(6)A~ cl.2
!
1/4 kWh
imp
Totalenergy
Signaling led
Partialenergy
Pulse output
blocks
Voltage lead
connectionblocks
Setting and
selectionkeys
Current lead
connectionblocks
Main page
Total meter
Partial meter
Backlighting status

Termékspecifikációk

Márka: Vemer
Kategória: Mérőberendezések
Modell: Energy-400 D PWRi

Szüksége van segítségre?

Ha segítségre van szüksége Vemer Energy-400 D PWRi, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók Mérőberendezések Vemer

Vemer

Vemer Energy-230 M Útmutató

2 Október 2024
Vemer

Vemer Energy-230 Wi-Fi Útmutató

31 Augusztus 2024
Vemer

Vemer Energy-230 Micro LCD Útmutató

5 Augusztus 2024
Vemer

Vemer Energy-3x130 PWRi Útmutató

28 Július 2024
Vemer

Vemer Energy-400 D90 Útmutató

25 Július 2024
Vemer

Vemer Energy-400 PWR Útmutató

25 Július 2024
Vemer

Vemer Energy-400 D PWR Útmutató

20 Július 2024
Vemer

Vemer Energy-230 Micro Útmutató

20 Július 2024
Vemer

Vemer Energy-230 LC Útmutató

17 Július 2024
Vemer

Vemer Energy-View Útmutató

13 Július 2024

Útmutatók Mérőberendezések

Legújabb útmutatók Mérőberendezések

Uni-T

Uni-T UT220 Útmutató

3 Április 2025
Uni-T

Uni-T UT681C Útmutató

3 Április 2025
Uni-T

Uni-T UT216C Útmutató

3 Április 2025
Uni-T

Uni-T UT611 Útmutató

3 Április 2025
Uni-T

Uni-T UT210D Útmutató

3 Április 2025
Uni-T

Uni-T UT210C Útmutató

3 Április 2025
Uni-T

Uni-T UT210B Útmutató

3 Április 2025
Uni-T

Uni-T UT682 Útmutató

3 Április 2025
Uni-T

Uni-T UT275 Útmutató

3 Április 2025
Uni-T

Uni-T UT08A Útmutató

3 Április 2025