Használati útmutató BlendMount BRD-2027

BlendMount nincs kategorizálva BRD-2027

Olvassa el alább 📖 a magyar nyelvű használati útmutatót BlendMount BRD-2027 (2 oldal) a nincs kategorizálva kategóriában. Ezt az útmutatót 21 ember találta hasznosnak és 11 felhasználó értékelte átlagosan 4.4 csillagra

Letöltés PDF

Oldal 1/2

PART# BRD-2027

Hlend

lllount-

:ra

::n

11111111111111~1111111111!

Innovative

Mounting

Solution

LEFT HAND DRIVE VEHICLE

28028

41125

INSTALLATION INSTRUCTIONS FOR BELTRONICS AND ESCORT RADAR DETECTORS

Your rear view

mirror

has

minimal

clearance between the back side

the

mirror

and the

mirror

stem.

very

important

that

this

mount

installed correctly

ensure

mirror

adjustability

retained.

PLEASE READ THESE INSTRUCTIONS THOROUGHLY BEFORE INSTALLING THIS MOUNT

BEFORE INSTALLING THIS MOUNT

YOUR MIRROR observe how the spring clip functions. When

used

properly,

the

spring

clip

avoids

putting

excess

pressure

the

mirror

when

installing

and

removing

the

radar

detector

(RD).

release tension from the spring clip, simply squeeze the

tab and the back side of the mount together. This will lower the bottom portion

the spring clip allowing you to slide the

and off the mount. Push

the

Release button and slide the RD onto the Spring Clip as far as it will go. Then release both the

Tab

and the Release Button. Slide the RD toward

you just slightly until you hear it lock into position. Install and remove the

a few times before installing the mount on your mirror.

TOP

SECTION

STEP 1 • Loosen the clamp screw so the top section separates

from the mid section. This will provide the necessary clearance to

slide the mount over the mirror stem as shown above.

Innovative Design

And

Precision Manufacturing

PPROXIMATELY 1/8"

BETW

ACK

MIRROR AND MOUN

STEP 2 -

ghten the clamp screw until the

Top

and Mid Sections are slight-

snug

around the mirror stem.

You

should still be able to move the mount

.1long the stem. Before fully lightening the clamp screw, slide the mount towardf

the windshield as far

it will go. There should be approximately 1/8" between

the back of the mirror and the mount as shown above.

PAGE 1 OF 2

BlendMount -

PATENT# D625,580 S. 0656,811 S. 0653,980 S

D690,245 S, D690,246 S, D690,247

Sand

other patents pending

PART# BRD-2027

Blend

fflo

_u_n_ ®

dED

Innovative

Mounting

Solution

ROTATING

ADJUSTMENT

DRIVER'S PERSPECTIVE

WITH NO ROTATING

ADJUSTMENT USED

DRIVER'S PERSPECTIVE

WITH

RADAR

ROTATED

TOWARDS DRIVER

CLAMP SCREW

CLAMP

SCREW MUST

SLIGHTLY LOOSENED

BEFORE MAKING

ROTATING ADJUSTMENT

SURE TO RETIGHTEN

AFTER ADJUSTMENT

MADE

STEP 3 • Install your radar detector onto the mount. Use the adjustments shown above to adjust the RD to your desired position.

recom-

mend adjusting the RD as close to the bottom

your mirror as you can. NOTE When the rotating adjustment is used to rotate the RD towards

the driver, the footprint

the RD is reduced as shown above. Be sure to tighten all

the adjustment screws after the adjustments are made.

STEP 4 • With the RD adjusted right below the mirror as recommended, you will probably not be able to get your fingers between the RD and mirror to

access the buttons. The spring clip allows you to push the front

the

downward with one finger and press the buttons with another finger

as shown above.

NOTE : This mount can get extremely hot when sitting in direct sunlight. If you intend to remove your RD frequently, you may want to install the two gray