Használati útmutató BlendMount BCB-2025

BlendMount nincs kategorizálva BCB-2025

Olvassa el alább 📖 a magyar nyelvű használati útmutatót BlendMount BCB-2025 (2 oldal) a nincs kategorizálva kategóriában. Ezt az útmutatót 12 ember találta hasznosnak és 6.5 felhasználó értékelte átlagosan 4.6 csillagra

Letöltés PDF

Oldal 1/2

PART# BCB-2025

Hien

oun-t®

HI~~

~~IJ

IJl

ljl

Innovat

Mount

Solut

ions

&cobra

LEFT HAND DRIVE VEHICLE

INSTALLATION INSTRUCTIONS FOR THE

COBRA

DSP-9200BT, SPX-7800BTl7700, SPX-6700,

AND

IRAD 900

RADAR

DETECTOR

Your rear

view

mirror

has

minimal

clearance between the back side

the

mirror

and

the

mirror

stem.

very Important

that

this

mount

installed

correctly

ensure

mirror

adjustabillty is retained.

PLEASE READ THESE INSTRUCTIONS THOROUGHLY BEFORE INSTALLING THIS MOUNT

NOTE: For illustratlon purposes, the mount and rear view mirror shown

these instructions may look

slightly different then YOUR

mount

and rear view mirror.

BOTTOM

SPRING

CLIP

PARALLEL

WITH

1 • The RELEASE Button

the radar detector (RD) Is NOT used with this

mount.

release the tension

the spring clip, simply squeeze the TRIGGER and the back side

the mount together. This will lower the bottom portion

the spring clip allowing you to

2 • The bottom

the spring clip must be parallel with the

top

the RD to slide in and out. SLIDE THE RD ONTO

THE

SPRING CLIP

FAR AS IT WILL

. Release the

trigger to secure the RD onto the mount. Before installing the

mount onto your rear view mirror, remove and install the RD a

few times so you can observe how the spring clip functions.

slide the RD on and off. When used property, the spring clip avoids putti

excessive

pressure on the mirror stem when installing and removing the

. The top portion

the mount should barely move when the two opposing forces are applied.

TOP

SECTION

MID

SECTION _

.._

BODY

ASSEMBLY

CLEARANCE

FOR

MIRROR

STEM

The BODY ASSEMBLY must be removed to gain access to the

CLAMP SCREW. Remove the two socket head screws as shown

above. Be sure to remove the lock washer with the top screw along with

the lock washer and flat washer with the bottom screw. Loosen the

CLAMP SCREW so there is enough clearance between the TOP and

MID SECTIONS to slide over the mirror stem.

Innovative Design

And

Precision Manufacturing

PIVOT

POINT

TOP AND MID

SECTIONS

MUST

TOUCH

AT THE PIVOT POINT

BEFORE CLAMP SCREW

IS FULLY TIGHTENED

4 -

ile sitting In the passenger seat, place the mount over the mirror

stem. Tighten the CLAMP SCREW until the mount starts to clamp onto the

mirror stem. As you are tightening the clamp

, MAKE SURE THE TOP

AND MID SECTIONS TOUCH AT THE PIVOT POINT. If they

not touch

at the pivot point.YOU HAVE

INCOMPATIBLE MIRROR TYPE FOR

THIS MOUNT. Position the mount as far forward as it will go and parallel to

the bottom

the mirror before fully tightening.

PAGE 1 OF 2

BlendMount - US

PATENT#

D625,580 S, D656,811 S, D653,980 S

D690,245 S,

0690

,246 S,

0690

,247

Sand

other patents pending

PART# BCB-2025

Bien

aunt-®

Innovative

Mounting

Solutions

PIVOT

ADJUSTMENT

5 - Reinstall the body assembly. Install the RD onto the mount. Make the necessary

adjustments as shown above. Using the vertical adjustment, we recommend you

adjust the RD so there is approximately 1/2" gap between the bottom of the

mirror and the top of the RD. After all adjustments are made, be sure to check that

all adjustment screws are tight. Grab the long arm

the alien wrench to assure that

these screws are securely tightened.

You

will not strip out the tapped holes

the

aircraft grade aluminum.

6 -

access the buttons

the RD you will need to gently push

downward on the front

the RD with one finger and push the de-

sired button with another finger. Then allow the

to return to it's

original position by gently letting it spring upward. When accessing

the buttons, be sure to push the RD downward just enough for your

finger to fit between the RD and mirror. Do not push down more

than what Is needed.

;,:

iNSTALLING R '

. - ....

SLIDE

RC)

ONTO

c-,.

- ,

· • SPRING CLIP AS

'LL

7 - When removing or installing the RD, squeeze the trigger and the back side

the mount together with one hand, and lift the front

the

upward with

the other hand before sliding the RD

off

onto the spring clip. You

must

11ft

the

front

the

upward

before

slldlng

off

onto

the

mount.

NOTE : This mount can get extremely hot when sitting in direct sunlight. If you intend to remove your RD frequently, you may want to install the two gray