Használati útmutató BlendMount BMX-2027

BlendMount nincs kategorizálva BMX-2027

Olvassa el alább 📖 a magyar nyelvű használati útmutatót BlendMount BMX-2027 (2 oldal) a nincs kategorizálva kategóriában. Ezt az útmutatót 11 ember találta hasznosnak és 6 felhasználó értékelte átlagosan 4.8 csillagra

Letöltés PDF

Oldal 1/2

PART# BMX-2027

llll~i~llJ~I

lllJ~l

Hien

aunt-®

Innovative

Mounting

Solutions

ESCORr

PASSPORT

MAX

LEFT HAND DRIVE VEHICLE

Your rear

view

mirror

has

minimal

clearance between the

back

side

the

mirror

and

the

mirror

stem

very

important

that

this

mount

installed

correctly

ensure

mirror

adjustability

retained.

PLEASE READ THESE INSTRUCTIONS THOROUGHLY BEFORE INSTALLING THIS MOUNT

BOTTOM OF SPRING CLIP

PARALLEL WITH RD

The RELEASE Button on the radar detector (RD) is NOT used with this mount.

release the tension

the spring clip, simply squeeze the TRIGGER and the back side of the

mount together. This will lower the bottom portion

the spring clip allowing you to slide the

RD on and off. When used properly, the spring clip avoids putting excessive pressure on the

mirror stem when installing and removing the

RD.

The top portion of

mount

should

barely move when the two opposing forces are applied. The bottom of the spring clip

must be parallel with the top

the RD to slide

and

out.

SLIDE THE RD ONTO THE

SPRING CLIP AS FAR AS IT

WILL

. Release the trigger to secure the RD onto the

mount. Before installing the mount onto your rear view mirror, remove and install the RD a

few times so you can observe how the spring clip functions.

With the

adjusted right below the mirror as recom-

mended, you will probably not be able to get your fin-

gers between the RD and mirror to access the buttons.

The

spring

clip

allows

you

push

the

front

the

RD downward with one finger and press the but-

tons with another finger as shown above.

PPROXIMATELY 1/8" BETWE

ACK

MIRROR AND MOUN

STEP 1 • Loosen the clamp screw so the top section separates

from the mid section. This will provide the necessary clearance to

slide the mount over the mirror stem as shown above.

STEP 2 - Tighten the clamp screw until the Top and Mid Sections are

slightly

snug

around the mirror stem. You should still be able to move the

mount along the stem. Before fully tightening the clamp screw, slide the mount

towards the windshield as far as It will go. There should be approximately 1/8"

between the back

the mirror and the mount as shown above.

Innovative Design

And

Precision Manufacturing

PAGE 1 OF 2

BlendMount - US PATENT# D625,580 S, D656,811

D653,980 S

D690,245

D690,246

D690,247

Sand

other patents pending

PART# BMX-2027

Hlen.d

lllount-®

ESCORT

PASSPORT

MAX

Innovative

Mounting

Solutions

CLAMP SCREW

CLAMP SCREW MUST

SLIGHTLY LOOSENED

BEFORE MAKING

ROTATING ADJUSTMENT

BE SURE TO RETIGHTEN

AFTER

ADJUSTMENT IS MADE

ROTATING

ADJUSTMENT

DRIVER'S PERSPECTIVE

WITH NO ROTATING

ADJUSTMENT USED

DRIVER'S PERSPECTIVE

WITH

RADAR

ROTATED

TOWARDS DRIVER

STEP 3 - Install your radar detector onto the mount. Use the adjustments shown above to adjust the RD to your desired position. We recom-

mend adjusting the RD as close to the bottom

your mirror as you can. NOTE When the rotating adjustment is used to rotate the RD towards

the driver, the footprint

the RD

reduced as shown above. Be sure to tighten all

the adjustment screws after the adjustments are made.

VERY IMPORTANT - When removing

installing the RD, squeeze the trigger and the back side

the mount together with one hand, and lift the front

the

RD upward with the other hand before sliding the RD off or onto the spring clip. You

must

lift

the

front

the

upward

before

sliding

off

onto

the

mount.

NOTE : This mount can get extremely hot when sitting in direct sunlight. If you intend to remove your RD frequently, you may want to Install the two gray

"TOUCH STRIPS" included